MTA Conductor Final Exam Signals, Procedures, and Safety
MTA Conductor Final Exam: Signals, Procedures, and Safety
Study online at https://quizlet.com/_jsenck
1. What is the routine cycle an- Stand clear of the closing doors, please.
nouncement made upon a regu-
lar stop?
2. What are the six instances to pull 1. Leaves the terminal before receiving the proceed sig-
the cord at the next station? nal. 2. Repeatedly stops short. 3. Continually makes hard
stops. 4. Repeated irregular acceleration and braking. 5.
Train Operator fails to respond to radio or public-address
communication. 6. Wrong route, unless OCC instructed the
movement.
3. What is the first step in the Close the section containing the defective door using the
R62/R62A door cut-out proce- MDC at the operating cab.
dure?
4. What should you do if an ob- Remove it, rotate the switch to NORMAL, and observe op-
struction is found during the eration.
R62/R62A door cut-out proce-
dure?
5. What is the announcement Stand clear of the closing doors, please.
made after all customers detrain
at a stub-end terminal?
6. What is the first action when ar- Bring the train to a proper stop at the terminal adjacent to
riving at a stub-end terminal? the Conductor's Indication Board.
7. What does a green signal indi- Proceed at allowable speed.
cate?
8. What does a yellow signal indi- Proceed with caution; be prepared to stop at the next
cate? signal.
1
, MTA Conductor Final Exam Signals, Procedures, and Safety
MTA Conductor Final Exam: Signals, Procedures, and Safety
Study online at https://quizlet.com/_jsenck
9. What does a red signal indicate? Stop.
10. What should be done if a blue Verify the emergency communication/equipment location
light station is encountered? and check the local equipment list.
11. What does a long signal from the STOP.
train buzzer mean?
12. What does two long signals from PROCEED.
the train buzzer mean?
13. What does three short signals REQUEST RCI (Road Car Inspector requested).
from the train buzzer mean?
14. What does a REQUEST ASSISTANCE.
long-short-long-short signal
from the train buzzer mean?
15. What does a black-and-white Conductor Indicator Board / proper conductor position.
striped board indicate?
16. What does a red-and-white No Clearance - hazard; employees must not occupy the
striped board indicate? area.
17. What should be done if the pan- Lock the door fully in the pocket and perform the Snap Test;
el cannot be restored during the notify RCC/OCC and report the defect.
door cut-out procedure?
18. What is the procedure if the door Return the switch to OFF and manually close the panel.
fails to close after removing an
obstruction?
19. To establish the new operating position.
2
MTA Conductor Final Exam: Signals, Procedures, and Safety
Study online at https://quizlet.com/_jsenck
1. What is the routine cycle an- Stand clear of the closing doors, please.
nouncement made upon a regu-
lar stop?
2. What are the six instances to pull 1. Leaves the terminal before receiving the proceed sig-
the cord at the next station? nal. 2. Repeatedly stops short. 3. Continually makes hard
stops. 4. Repeated irregular acceleration and braking. 5.
Train Operator fails to respond to radio or public-address
communication. 6. Wrong route, unless OCC instructed the
movement.
3. What is the first step in the Close the section containing the defective door using the
R62/R62A door cut-out proce- MDC at the operating cab.
dure?
4. What should you do if an ob- Remove it, rotate the switch to NORMAL, and observe op-
struction is found during the eration.
R62/R62A door cut-out proce-
dure?
5. What is the announcement Stand clear of the closing doors, please.
made after all customers detrain
at a stub-end terminal?
6. What is the first action when ar- Bring the train to a proper stop at the terminal adjacent to
riving at a stub-end terminal? the Conductor's Indication Board.
7. What does a green signal indi- Proceed at allowable speed.
cate?
8. What does a yellow signal indi- Proceed with caution; be prepared to stop at the next
cate? signal.
1
, MTA Conductor Final Exam Signals, Procedures, and Safety
MTA Conductor Final Exam: Signals, Procedures, and Safety
Study online at https://quizlet.com/_jsenck
9. What does a red signal indicate? Stop.
10. What should be done if a blue Verify the emergency communication/equipment location
light station is encountered? and check the local equipment list.
11. What does a long signal from the STOP.
train buzzer mean?
12. What does two long signals from PROCEED.
the train buzzer mean?
13. What does three short signals REQUEST RCI (Road Car Inspector requested).
from the train buzzer mean?
14. What does a REQUEST ASSISTANCE.
long-short-long-short signal
from the train buzzer mean?
15. What does a black-and-white Conductor Indicator Board / proper conductor position.
striped board indicate?
16. What does a red-and-white No Clearance - hazard; employees must not occupy the
striped board indicate? area.
17. What should be done if the pan- Lock the door fully in the pocket and perform the Snap Test;
el cannot be restored during the notify RCC/OCC and report the defect.
door cut-out procedure?
18. What is the procedure if the door Return the switch to OFF and manually close the panel.
fails to close after removing an
obstruction?
19. To establish the new operating position.
2
