CIP PRACTICE SET 2026 RISK
MANAGEMENT QUESTIONS HIGH YIELD A+
◉ Common errors that may produce inaccurate readings when using
a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge
include
SELECT THAT ALL APPLY:
A. failing to determine the base metal reading (BMR)
B. rotating the dial too fast when taking measurements
C. taking measurements too far from the edge of a surface
D. measuring ditty, tacky, or soft films
Answer: failing to determine the base metal reading (BMR)
rotating the dial too fast when taking measurements
measuring ditty, tacky, or soft films
◉ Conventional spray is a good choice when:
A. high production rates are required
B. high quality finishes are required
C. high transfer efficiency is required
D. high viscosity coatings are being applied
Answer: high quality finishes are required
,◉ Which of these tests uses a syringe?
A. sleeve test
B. potassium ferricyanide
C. bresle patch
D. soluble salts meter
Answer: bresle patch
◉ Which one of these elements is not necessary for corrosion to
occur:
A. anode
B. cathode
C. reference cell
D. electrolyte
Answer: reference cell
◉ Digital hygrometers -
A. consist of a bimetallic sensing element protected from wing gusts
B. are used to measure temperature from a distance
C. use a thermocouple in contact with the surface to measure
temperature
, D. determine relative humidity, air temperature, and dew point
temperature
Answer: determine relative humidity, air temperature, and dew
point temperature
◉ Using SSPC Vis 1 as a guide when performing a visual inspection
of a steel surface prior to surface preparation a NACE inspector
would assign which designations to the surface condition:
A. Rust Grades A-D
B. Surface Conditions E-G
C. Rust Grades 1-4
D. Surface Condition H
Answer: Rust Grades A-D
◉ Inspector's daily reports are used:
SELECT THAT ALL APPLY
A. by the contractor to estimate the amount of work done that day
B. to provide continuity between inspectors
C. to aid in arbitration between the contractor and client
D. to help in cases of a coating failure
Answer: by the contractor to estimate the amount of work done that
day
MANAGEMENT QUESTIONS HIGH YIELD A+
◉ Common errors that may produce inaccurate readings when using
a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge
include
SELECT THAT ALL APPLY:
A. failing to determine the base metal reading (BMR)
B. rotating the dial too fast when taking measurements
C. taking measurements too far from the edge of a surface
D. measuring ditty, tacky, or soft films
Answer: failing to determine the base metal reading (BMR)
rotating the dial too fast when taking measurements
measuring ditty, tacky, or soft films
◉ Conventional spray is a good choice when:
A. high production rates are required
B. high quality finishes are required
C. high transfer efficiency is required
D. high viscosity coatings are being applied
Answer: high quality finishes are required
,◉ Which of these tests uses a syringe?
A. sleeve test
B. potassium ferricyanide
C. bresle patch
D. soluble salts meter
Answer: bresle patch
◉ Which one of these elements is not necessary for corrosion to
occur:
A. anode
B. cathode
C. reference cell
D. electrolyte
Answer: reference cell
◉ Digital hygrometers -
A. consist of a bimetallic sensing element protected from wing gusts
B. are used to measure temperature from a distance
C. use a thermocouple in contact with the surface to measure
temperature
, D. determine relative humidity, air temperature, and dew point
temperature
Answer: determine relative humidity, air temperature, and dew
point temperature
◉ Using SSPC Vis 1 as a guide when performing a visual inspection
of a steel surface prior to surface preparation a NACE inspector
would assign which designations to the surface condition:
A. Rust Grades A-D
B. Surface Conditions E-G
C. Rust Grades 1-4
D. Surface Condition H
Answer: Rust Grades A-D
◉ Inspector's daily reports are used:
SELECT THAT ALL APPLY
A. by the contractor to estimate the amount of work done that day
B. to provide continuity between inspectors
C. to aid in arbitration between the contractor and client
D. to help in cases of a coating failure
Answer: by the contractor to estimate the amount of work done that
day
