Texas Plumbing Journeyman EXAM, /GET IT 100% ACCURATE!! 2026/2027!
MOST TESTED QUESTIONS AND VERIFIED SOLUTIONS
1. Fixture connections that require the removal of an ac- Accessible
cess panel for servicing are considered
2. That part of the lowest piping of a drainage system Building sewer
that receives the discharge from soil, waste, and other
drainage pipes inside the walls fo the building and
conveys it to a point 2 feet outside the building wall is
a
3. A vertical vent that is a continuation of the drain to Circuit vent
which it connects is a
4. A horizontal drain that is sized to provide free move- Continuous waste system
ment of air above the flow line of the drain is called a
5. The length along the centerline of the pipe and fittings Diameter length
is the
6. A device integrated within an air accumulator vessel Expansion tank
that is designed to discharge a predetermined quanti-
ty of water to fixtures for flushing purposes is a
7. The combination of fittings that may be used to make 1-45 degree and 1-45de-
an offset and is considered a vertical pipe are gree
8. Water safe for drinking and culinary purposes is re- Potable water
ferred to as
9. By code definition, a stack is always Vertical
10. A vent that also serves as a drain is a Wet vent
11. Diagonal pipe
1/9
, Texas Plumbing Journeyman EXAM, /GET IT 100% ACCURATE!! 2026/2027!
MOST TESTED QUESTIONS AND VERIFIED SOLUTIONS
A pipe that makes an angle of not more than 45 de-
grees with the vertical is considered
12. he vertical depth of a trap seal is measured from The outlet of the trap to the
bottom of the trap
13. A mixing valve that senses outlet temperature and Thermostatic (tempera-
compensates for fluctuations in incoming hot or cold ture control) valve
water temperature is a
14. The lowest portion of the inside of a horizontal pipe is Bottom
called the
15. PEX is the acronym for Cross-linked polyethylene
16. A confined space is a room or space having a volume 100 cubic feet per BTU/hr.
equal to at least ______ of the aggregate input rating of
all the fuel-burning appliances in that space.
17. A joint obtained by the joining of metal parts with Soldered joint
metallic mixtures or alloys that melt at a temperature
up to 840 degrees is a
18. The organization, office, or individual responsible for Plumbing Inspector
enforcing the requirements of a
code or standard is the
19. That portion of a drainage system that does not drain Sewer ejector
by gravity into the building sewer is known as a
20. A pipe inside a building that conveys storm water from Building storm drain
the roof to a storm drain is called a (an)
2/9
MOST TESTED QUESTIONS AND VERIFIED SOLUTIONS
1. Fixture connections that require the removal of an ac- Accessible
cess panel for servicing are considered
2. That part of the lowest piping of a drainage system Building sewer
that receives the discharge from soil, waste, and other
drainage pipes inside the walls fo the building and
conveys it to a point 2 feet outside the building wall is
a
3. A vertical vent that is a continuation of the drain to Circuit vent
which it connects is a
4. A horizontal drain that is sized to provide free move- Continuous waste system
ment of air above the flow line of the drain is called a
5. The length along the centerline of the pipe and fittings Diameter length
is the
6. A device integrated within an air accumulator vessel Expansion tank
that is designed to discharge a predetermined quanti-
ty of water to fixtures for flushing purposes is a
7. The combination of fittings that may be used to make 1-45 degree and 1-45de-
an offset and is considered a vertical pipe are gree
8. Water safe for drinking and culinary purposes is re- Potable water
ferred to as
9. By code definition, a stack is always Vertical
10. A vent that also serves as a drain is a Wet vent
11. Diagonal pipe
1/9
, Texas Plumbing Journeyman EXAM, /GET IT 100% ACCURATE!! 2026/2027!
MOST TESTED QUESTIONS AND VERIFIED SOLUTIONS
A pipe that makes an angle of not more than 45 de-
grees with the vertical is considered
12. he vertical depth of a trap seal is measured from The outlet of the trap to the
bottom of the trap
13. A mixing valve that senses outlet temperature and Thermostatic (tempera-
compensates for fluctuations in incoming hot or cold ture control) valve
water temperature is a
14. The lowest portion of the inside of a horizontal pipe is Bottom
called the
15. PEX is the acronym for Cross-linked polyethylene
16. A confined space is a room or space having a volume 100 cubic feet per BTU/hr.
equal to at least ______ of the aggregate input rating of
all the fuel-burning appliances in that space.
17. A joint obtained by the joining of metal parts with Soldered joint
metallic mixtures or alloys that melt at a temperature
up to 840 degrees is a
18. The organization, office, or individual responsible for Plumbing Inspector
enforcing the requirements of a
code or standard is the
19. That portion of a drainage system that does not drain Sewer ejector
by gravity into the building sewer is known as a
20. A pipe inside a building that conveys storm water from Building storm drain
the roof to a storm drain is called a (an)
2/9
