___________________________________________________________________
Certified Furniture Technician Questions
And Correct Answers (Verified Answers)
Plus Rationales 2026 Q&A Instant
Download Pdf
___________________________________________________________________
1. What is the primary purpose of a furniture technician’s inspection before
beginning a repair?
A. To determine the furniture’s resale value
B. To identify damage, construction methods, materials, and repair
requirements
C. To replace all visible hardware
D. To determine the customer’s preferred color
Answer: To identify damage, construction methods, materials, and repair
requirements
Rationale: A thorough inspection establishes the condition, construction,
materials, and appropriate repair approach before work begins.
2. Which wood characteristic most commonly indicates that a board was cut
from the center portion of a log?
A. Flat grain
B. Quarter-sawn grain
C. End grain
D. Cross grain
Answer: Quarter-sawn grain
,Rationale: Quarter-sawn lumber is cut radially from the log and commonly
displays relatively straight grain and characteristic ray patterns.
3. What is the primary reason wood furniture expands and contracts?
A. Changes in humidity
B. Changes in paint color
C. Changes in screw size
D. Changes in lighting
Answer: Changes in humidity
Rationale: Wood is hygroscopic, meaning it gains or loses moisture from
surrounding air, causing dimensional movement.
4. Which adhesive is commonly used for traditional wood furniture joints?
A. Wood glue
B. Silicone caulk
C. Contact cement only
D. Thread locker
Answer: Wood glue
Rationale: Wood adhesives are specifically formulated to bond porous wood
surfaces and are widely used in furniture joinery.
5. What is the purpose of a furniture clamp during glue-up?
A. To remove the finish
B. To apply and maintain pressure while the adhesive cures
C. To sharpen the wood
D. To measure moisture
Answer: To apply and maintain pressure while the adhesive cures
Rationale: Proper clamping keeps mating surfaces aligned and maintains
sufficient pressure for a strong adhesive bond.
6. Which joint uses a projecting wooden member that fits into a
corresponding opening?
, A. Butt joint
B. Mortise-and-tenon joint
C. Lap joint
D. Miter joint
Answer: Mortise-and-tenon joint
Rationale: A tenon projects from one component and fits into a mortise cut into
the mating component.
7. What is a common advantage of a dovetail joint?
A. It requires no fitting
B. It provides strong mechanical resistance to being pulled apart
C. It eliminates the need for wood
D. It is used only on metal furniture
Answer: It provides strong mechanical resistance to being pulled apart
Rationale: The interlocking geometry of dovetails provides excellent mechanical
strength, particularly in drawer construction.
8. Which tool is most appropriate for checking whether two surfaces meet at
a 90-degree angle?
A. Combination square
B. Awl
C. Block plane
D. Cabinet scraper
Answer: Combination square
Rationale: A combination square can be used to check and mark accurate 90-
degree and other common angles.
9. What should a technician do before sanding a previously finished surface?
A. Increase the sanding pressure immediately
B. Identify the existing finish and determine whether sanding is appropriate
, C. Apply wax
D. Soak the furniture in water
Answer: Identify the existing finish and determine whether sanding is
appropriate
Rationale: Some finishes, veneers, and surface treatments can be damaged by
aggressive sanding.
10.Which sanding technique generally produces the best surface?
A. Sanding randomly in every direction
B. Progressing through increasingly finer abrasives
C. Using only coarse sandpaper
D. Skipping directly to polishing compound
Answer: Progressing through increasingly finer abrasives
Rationale: Moving systematically from coarse to finer abrasives removes
scratches while progressively refining the surface.
11.What is veneer?
A. Solid metal attached to wood
B. A thin layer of wood applied over a substrate
C. A type of upholstery foam
D. A chemical wood preservative
Answer: A thin layer of wood applied over a substrate
Rationale: Veneer is thin wood material bonded to another surface, allowing
attractive grain patterns while conserving solid lumber.
12.Why must a technician use extra care when sanding veneer?
A. Veneer cannot be glued
B. The thin wood layer can be sanded through
C. Veneer is always made from plastic
D. Veneer expands more than steel
Answer: The thin wood layer can be sanded through
Certified Furniture Technician Questions
And Correct Answers (Verified Answers)
Plus Rationales 2026 Q&A Instant
Download Pdf
___________________________________________________________________
1. What is the primary purpose of a furniture technician’s inspection before
beginning a repair?
A. To determine the furniture’s resale value
B. To identify damage, construction methods, materials, and repair
requirements
C. To replace all visible hardware
D. To determine the customer’s preferred color
Answer: To identify damage, construction methods, materials, and repair
requirements
Rationale: A thorough inspection establishes the condition, construction,
materials, and appropriate repair approach before work begins.
2. Which wood characteristic most commonly indicates that a board was cut
from the center portion of a log?
A. Flat grain
B. Quarter-sawn grain
C. End grain
D. Cross grain
Answer: Quarter-sawn grain
,Rationale: Quarter-sawn lumber is cut radially from the log and commonly
displays relatively straight grain and characteristic ray patterns.
3. What is the primary reason wood furniture expands and contracts?
A. Changes in humidity
B. Changes in paint color
C. Changes in screw size
D. Changes in lighting
Answer: Changes in humidity
Rationale: Wood is hygroscopic, meaning it gains or loses moisture from
surrounding air, causing dimensional movement.
4. Which adhesive is commonly used for traditional wood furniture joints?
A. Wood glue
B. Silicone caulk
C. Contact cement only
D. Thread locker
Answer: Wood glue
Rationale: Wood adhesives are specifically formulated to bond porous wood
surfaces and are widely used in furniture joinery.
5. What is the purpose of a furniture clamp during glue-up?
A. To remove the finish
B. To apply and maintain pressure while the adhesive cures
C. To sharpen the wood
D. To measure moisture
Answer: To apply and maintain pressure while the adhesive cures
Rationale: Proper clamping keeps mating surfaces aligned and maintains
sufficient pressure for a strong adhesive bond.
6. Which joint uses a projecting wooden member that fits into a
corresponding opening?
, A. Butt joint
B. Mortise-and-tenon joint
C. Lap joint
D. Miter joint
Answer: Mortise-and-tenon joint
Rationale: A tenon projects from one component and fits into a mortise cut into
the mating component.
7. What is a common advantage of a dovetail joint?
A. It requires no fitting
B. It provides strong mechanical resistance to being pulled apart
C. It eliminates the need for wood
D. It is used only on metal furniture
Answer: It provides strong mechanical resistance to being pulled apart
Rationale: The interlocking geometry of dovetails provides excellent mechanical
strength, particularly in drawer construction.
8. Which tool is most appropriate for checking whether two surfaces meet at
a 90-degree angle?
A. Combination square
B. Awl
C. Block plane
D. Cabinet scraper
Answer: Combination square
Rationale: A combination square can be used to check and mark accurate 90-
degree and other common angles.
9. What should a technician do before sanding a previously finished surface?
A. Increase the sanding pressure immediately
B. Identify the existing finish and determine whether sanding is appropriate
, C. Apply wax
D. Soak the furniture in water
Answer: Identify the existing finish and determine whether sanding is
appropriate
Rationale: Some finishes, veneers, and surface treatments can be damaged by
aggressive sanding.
10.Which sanding technique generally produces the best surface?
A. Sanding randomly in every direction
B. Progressing through increasingly finer abrasives
C. Using only coarse sandpaper
D. Skipping directly to polishing compound
Answer: Progressing through increasingly finer abrasives
Rationale: Moving systematically from coarse to finer abrasives removes
scratches while progressively refining the surface.
11.What is veneer?
A. Solid metal attached to wood
B. A thin layer of wood applied over a substrate
C. A type of upholstery foam
D. A chemical wood preservative
Answer: A thin layer of wood applied over a substrate
Rationale: Veneer is thin wood material bonded to another surface, allowing
attractive grain patterns while conserving solid lumber.
12.Why must a technician use extra care when sanding veneer?
A. Veneer cannot be glued
B. The thin wood layer can be sanded through
C. Veneer is always made from plastic
D. Veneer expands more than steel
Answer: The thin wood layer can be sanded through
