ASE G1 Test Prep (General Automobile Maintenance) Questions and
Answers Rated A
Toe can cause tire wear if not within manufacturer's spec-
ifications True
(True or False)
Camber can cause tire wear if not within manufacturer's
specifications True
(True or False)
Caster can cause tire wear if not within manufacturer's
specifications False
(True or False)
Technician A says that a PAX run-flat tire uses a special
wheel.
Technician B says that a standard tire can be used to Technician A only
replace a PAX run-flat tire.
Which technician is correct ?
Wheel back spacing is also called ? Rear spacing
A tire is labeled 215/60R15 92T ; the 92 indicates what ? Load rating
What do the letter "J J" mean in a wheel designation size
The shape of the flange area
labeled 14 x 7JJ
A tire is labeled 215/60R15 92T ; the T indicates what ? Speed rating
When purchasing replacement tires, do not change tire
10 mm
width from the stock size by more than ?
Which type of disc brake caliper may leak brake fluid more
Fixed disc brake caliper
often ?
Brake fluid boiling point can be measured using ? A Boiling Point Tester
What principle is used to create high voltage from low
Electromagnetic induction
voltage?
The Aspect Ratio of a tire means what ? The ratio of height to width
,ASE G1 Test Prep (General Automobile Maintenance) Questions and
Answers Rated A
The pickup coil or trigger is usually electrically connected
Ignition Module
to the ?
Semi-metallic brake pads are made by a process called ? Sintering
Which of these takes place during regeneration in a Diesel
Soot is being burned
Particulate Filter (DPF)?
The brake pad edge code letters "FF" mean what ? Coeflcient of Friction Rating
Engine oil level should be checked .... With the vehicle parked on level ground
A quick-take-up master cylinder is required when what
Low-Drag caliper
type of caliper design is used on a vehicle ?
What part should be removed to test cylinder compres-
Glow plug or injector
sion on a diesel engine?
Technician A says that maintenance-free batteries use a
large amount of water.
Technician B says that maintenance-free batteries use
Technician B only
materials that reduce the amount of water used by the
battery.
Which technician is correct?
What part causes the disc brake caliper piston to retract
The Square-Cut O-ring
when the brakes are released ?
Adding a chemical to make ethylene glycol bitter to the
Embittered
taste is called ?
All safety glasses should meet standards set by ? ANSI (American National Standards Institute)
A potentiometer, a three-wire variable resistor, is used in
Throttle Position Sensor (TPS)
which type of sensor?
Technician A says that galvanic activity is the result of a
poor ground connection. Technician B only
Technician B says that electrolysis can occur with a poor
, ASE G1 Test Prep (General Automobile Maintenance) Questions and
Answers Rated A
ground connection.
Which technician is correct?
Where is the fuel-pressure regulator located on a vacu-
At the outlet of the fuel rail
um-biased port fuel-injection system?
Oil viscosity indicates what ? Tendency of oil to resist flowing
Technician A says that with self-adjusting clutch systems,
the release bearing constantly rotates.
Technician B says the ball bearing portion of the re-
Technician A only
lease bearing should be lubricated with high temperature
grease during routine maintenance.
Which technician is correct?
Hydroplaning can occur at speeds as low as ? 30 mph
Battery hold-down clamps or brackets help reduce
, which can greatly reduce the capacity Vibration
and life of any battery.
A starter can be constructed in a smaller size due to the
Gear reduction
use of and permanent magnets.
Two technician are discussing the need for history of the
vehicle. Technician A says that an accident could cause
faults due to hidden damage.
Both Technicians A and B
Technician B says that some faults could be related to a
previous repair.
Which technician is correct?
Technician A says the gear reduction occurs when the
drive gear turns faster than the driven gear.
Technician B says that overdrive occurs when the driven Both Technicians A and B
gear turns faster than the drive gear.
Which technician is correct?
Answers Rated A
Toe can cause tire wear if not within manufacturer's spec-
ifications True
(True or False)
Camber can cause tire wear if not within manufacturer's
specifications True
(True or False)
Caster can cause tire wear if not within manufacturer's
specifications False
(True or False)
Technician A says that a PAX run-flat tire uses a special
wheel.
Technician B says that a standard tire can be used to Technician A only
replace a PAX run-flat tire.
Which technician is correct ?
Wheel back spacing is also called ? Rear spacing
A tire is labeled 215/60R15 92T ; the 92 indicates what ? Load rating
What do the letter "J J" mean in a wheel designation size
The shape of the flange area
labeled 14 x 7JJ
A tire is labeled 215/60R15 92T ; the T indicates what ? Speed rating
When purchasing replacement tires, do not change tire
10 mm
width from the stock size by more than ?
Which type of disc brake caliper may leak brake fluid more
Fixed disc brake caliper
often ?
Brake fluid boiling point can be measured using ? A Boiling Point Tester
What principle is used to create high voltage from low
Electromagnetic induction
voltage?
The Aspect Ratio of a tire means what ? The ratio of height to width
,ASE G1 Test Prep (General Automobile Maintenance) Questions and
Answers Rated A
The pickup coil or trigger is usually electrically connected
Ignition Module
to the ?
Semi-metallic brake pads are made by a process called ? Sintering
Which of these takes place during regeneration in a Diesel
Soot is being burned
Particulate Filter (DPF)?
The brake pad edge code letters "FF" mean what ? Coeflcient of Friction Rating
Engine oil level should be checked .... With the vehicle parked on level ground
A quick-take-up master cylinder is required when what
Low-Drag caliper
type of caliper design is used on a vehicle ?
What part should be removed to test cylinder compres-
Glow plug or injector
sion on a diesel engine?
Technician A says that maintenance-free batteries use a
large amount of water.
Technician B says that maintenance-free batteries use
Technician B only
materials that reduce the amount of water used by the
battery.
Which technician is correct?
What part causes the disc brake caliper piston to retract
The Square-Cut O-ring
when the brakes are released ?
Adding a chemical to make ethylene glycol bitter to the
Embittered
taste is called ?
All safety glasses should meet standards set by ? ANSI (American National Standards Institute)
A potentiometer, a three-wire variable resistor, is used in
Throttle Position Sensor (TPS)
which type of sensor?
Technician A says that galvanic activity is the result of a
poor ground connection. Technician B only
Technician B says that electrolysis can occur with a poor
, ASE G1 Test Prep (General Automobile Maintenance) Questions and
Answers Rated A
ground connection.
Which technician is correct?
Where is the fuel-pressure regulator located on a vacu-
At the outlet of the fuel rail
um-biased port fuel-injection system?
Oil viscosity indicates what ? Tendency of oil to resist flowing
Technician A says that with self-adjusting clutch systems,
the release bearing constantly rotates.
Technician B says the ball bearing portion of the re-
Technician A only
lease bearing should be lubricated with high temperature
grease during routine maintenance.
Which technician is correct?
Hydroplaning can occur at speeds as low as ? 30 mph
Battery hold-down clamps or brackets help reduce
, which can greatly reduce the capacity Vibration
and life of any battery.
A starter can be constructed in a smaller size due to the
Gear reduction
use of and permanent magnets.
Two technician are discussing the need for history of the
vehicle. Technician A says that an accident could cause
faults due to hidden damage.
Both Technicians A and B
Technician B says that some faults could be related to a
previous repair.
Which technician is correct?
Technician A says the gear reduction occurs when the
drive gear turns faster than the driven gear.
Technician B says that overdrive occurs when the driven Both Technicians A and B
gear turns faster than the drive gear.
Which technician is correct?
