Maryland Structural Steel Erector
Certification Exam Practice Questions
And Correct Answers (Verified Answers)
Plus Rationale 2026 Q&A| Instant
Download Pdf
1. A structural steel erector is primarily responsible for which of the
following tasks?
A. Installing electrical conduit in steel frames
B. Designing structural steel members for buildings
C. Assembling and securing steel framework on construction sites
D. Manufacturing steel beams in a factory
C
Structural steel erectors focus on assembling, positioning, and
securing steel components on-site to form the skeleton of buildings
and structures.
2. Under OSHA Subpart R, what is the minimum training requirement
before a worker can engage in steel erection activities?
A. A college engineering degree
B. A site-specific safety training program
C. A welding certification only
D. No formal training is required
, B
OSHA requires employers to provide site-specific training to ensure
workers understand hazards unique to steel erection operations.
3. Which device is most commonly used to lift heavy steel beams into
place?
A. Hydraulic jack
B. Crane
C. Forklift hand truck
D. Air compressor
B
Cranes are the primary lifting equipment used to safely position
heavy steel members during erection.
4. What is the primary purpose of a “tag line” during steel erection?
A. To measure beam length
B. To guide and control loads while being lifted
C. To tighten bolts in connections
D. To weld beam joints
B
Tag lines are used to stabilize and control swinging loads during
crane operations.
5. Which of the following is a critical personal fall protection system
component?
A. Hard hat only
B. Safety vest
C. Full-body harness
D. Leather gloves
C
A full-body harness distributes fall forces across the body to reduce
injury risk during falls.
, 6. What is the primary function of a steel “girder”?
A. To decorate building facades
B. To support loads across long spans
C. To provide insulation
D. To act as temporary scaffolding
B
Girders are major horizontal structural members designed to carry
heavy loads over long distances.
7. Which of the following is used to connect structural steel members
temporarily during erection?
A. Drift pins
B. Plastic anchors
C. Concrete nails
D. Adhesive glue
A
Drift pins help align and temporarily secure steel members before
final bolting or welding.
8. What is the most common hazard in steel erection work?
A. Noise exposure only
B. Falling from heights
C. Radiation exposure
D. Chemical burns from acids
B
Falls are the leading cause of fatalities in steel erection due to
elevated work conditions.
9. What is the purpose of a “connection bolt” in steel structures?
A. To paint steel members
B. To permanently secure steel components together
C. To measure load capacity
Certification Exam Practice Questions
And Correct Answers (Verified Answers)
Plus Rationale 2026 Q&A| Instant
Download Pdf
1. A structural steel erector is primarily responsible for which of the
following tasks?
A. Installing electrical conduit in steel frames
B. Designing structural steel members for buildings
C. Assembling and securing steel framework on construction sites
D. Manufacturing steel beams in a factory
C
Structural steel erectors focus on assembling, positioning, and
securing steel components on-site to form the skeleton of buildings
and structures.
2. Under OSHA Subpart R, what is the minimum training requirement
before a worker can engage in steel erection activities?
A. A college engineering degree
B. A site-specific safety training program
C. A welding certification only
D. No formal training is required
, B
OSHA requires employers to provide site-specific training to ensure
workers understand hazards unique to steel erection operations.
3. Which device is most commonly used to lift heavy steel beams into
place?
A. Hydraulic jack
B. Crane
C. Forklift hand truck
D. Air compressor
B
Cranes are the primary lifting equipment used to safely position
heavy steel members during erection.
4. What is the primary purpose of a “tag line” during steel erection?
A. To measure beam length
B. To guide and control loads while being lifted
C. To tighten bolts in connections
D. To weld beam joints
B
Tag lines are used to stabilize and control swinging loads during
crane operations.
5. Which of the following is a critical personal fall protection system
component?
A. Hard hat only
B. Safety vest
C. Full-body harness
D. Leather gloves
C
A full-body harness distributes fall forces across the body to reduce
injury risk during falls.
, 6. What is the primary function of a steel “girder”?
A. To decorate building facades
B. To support loads across long spans
C. To provide insulation
D. To act as temporary scaffolding
B
Girders are major horizontal structural members designed to carry
heavy loads over long distances.
7. Which of the following is used to connect structural steel members
temporarily during erection?
A. Drift pins
B. Plastic anchors
C. Concrete nails
D. Adhesive glue
A
Drift pins help align and temporarily secure steel members before
final bolting or welding.
8. What is the most common hazard in steel erection work?
A. Noise exposure only
B. Falling from heights
C. Radiation exposure
D. Chemical burns from acids
B
Falls are the leading cause of fatalities in steel erection due to
elevated work conditions.
9. What is the purpose of a “connection bolt” in steel structures?
A. To paint steel members
B. To permanently secure steel components together
C. To measure load capacity
