EPIC: WILLOW EXAM STUDY GUIDE LATEST 2026 UPDATED
QUESTIONS AND VERIFIED 100% SOLUTIONS (2026/2027)
GRADE: A+|STATUS: GUARANTEED PASS
1) You're configuring a mixture for EXAMPALIN 20 OR 40 UNITS/ML IN D5W INFUSION. It has
these properties:
· The dose is usually 0.5 or 1 Unit/kg/hr.
· The frequency is "Continuous" and the route is "Intravenous."
· There should be two choices for concentration in the Order Composer: "20 Units/mL" and "40
Units/mL".
· The mixture is always prepared in 250 mL of D5W. The concentration affects how much
EXAMPALIN 100 UNITS/ML IJ SOLN is put in the bag.
Based on these details, answer the following:
a) What type of mixture is this? (pick 1)
a. IV Fluid Mixture
b. Main Ingredient Mixture
c. Ratio-Based Mixture
d. Concentration-Based Mixture - Answers -a.Wrong! It's not a ratio-based mixture, it's a
concentration-based mixture
c.WRONG! You don't put the multiple concentrations on MIXTURE SETUP 2. You put them on
the CONCENTRATION OPTIONS screen. See ch 10
If there was only one concentration, you could do it like this
D. Correct. It's always in this volume
E. Correct! There's only one base, so it should always be selected.
1|Page
, NOTE: You should not configure the ORDER COMPOSER SECTION SETUP screen to say "Base" >>
Allow only one? "Yes" and Selection Required? "Yes" Since there's only 1 base, and it's always
selected, this will throw an error.
You probably SHOULD set Allow custom dose? To "No" for the D5W on the MIXTURE ORDER
COMPOSER ITEMS screen.
a) Which OCC should you use? (pick 1)
a. RX SIMPLE MED
b. RX MAINTENANCE IV
c. RX MAIN INGREDIENT MIXTURE NO COMPONENTS DISPLAYED
d. RX MAIN INGREDIENT MIXTURE DISPLAYING BASE
e. RX CONCENTRATION DOSED MIXTURE
f. RX CONCENTRATION DOSED MIXTURE DISPLAYING BASE - Answers -E, RX CONCENTRATION
DOSED MIXTURE. There's only 1 base, so use this one (which doesn't display to base to end
users).
When the concentration of "20 Units/mL" is selected, the Order Name for this mixture should
be:exampalin (Learnix) 5,000 Units in dextrose 5% 250 mL (20 units/mL) infusionIf they choose
"40 Units/mL," the name should change to match. Assume that the EXAMPALIN 100 UNITS/ML
IJ SOLN and the DEXTROSE 5 % IV SOLN are already configured appropriately. What settings in
the MIXTURE record would you make to get the name to appear as described? - Answers -
Mixture suffix: "infusion"
Order Entry and After Ordering naming extension: 4083492101 - IP RXNAME DOSE WITH BASE,
STRENGTH, AND TOTAL VOLUME
2|Page
QUESTIONS AND VERIFIED 100% SOLUTIONS (2026/2027)
GRADE: A+|STATUS: GUARANTEED PASS
1) You're configuring a mixture for EXAMPALIN 20 OR 40 UNITS/ML IN D5W INFUSION. It has
these properties:
· The dose is usually 0.5 or 1 Unit/kg/hr.
· The frequency is "Continuous" and the route is "Intravenous."
· There should be two choices for concentration in the Order Composer: "20 Units/mL" and "40
Units/mL".
· The mixture is always prepared in 250 mL of D5W. The concentration affects how much
EXAMPALIN 100 UNITS/ML IJ SOLN is put in the bag.
Based on these details, answer the following:
a) What type of mixture is this? (pick 1)
a. IV Fluid Mixture
b. Main Ingredient Mixture
c. Ratio-Based Mixture
d. Concentration-Based Mixture - Answers -a.Wrong! It's not a ratio-based mixture, it's a
concentration-based mixture
c.WRONG! You don't put the multiple concentrations on MIXTURE SETUP 2. You put them on
the CONCENTRATION OPTIONS screen. See ch 10
If there was only one concentration, you could do it like this
D. Correct. It's always in this volume
E. Correct! There's only one base, so it should always be selected.
1|Page
, NOTE: You should not configure the ORDER COMPOSER SECTION SETUP screen to say "Base" >>
Allow only one? "Yes" and Selection Required? "Yes" Since there's only 1 base, and it's always
selected, this will throw an error.
You probably SHOULD set Allow custom dose? To "No" for the D5W on the MIXTURE ORDER
COMPOSER ITEMS screen.
a) Which OCC should you use? (pick 1)
a. RX SIMPLE MED
b. RX MAINTENANCE IV
c. RX MAIN INGREDIENT MIXTURE NO COMPONENTS DISPLAYED
d. RX MAIN INGREDIENT MIXTURE DISPLAYING BASE
e. RX CONCENTRATION DOSED MIXTURE
f. RX CONCENTRATION DOSED MIXTURE DISPLAYING BASE - Answers -E, RX CONCENTRATION
DOSED MIXTURE. There's only 1 base, so use this one (which doesn't display to base to end
users).
When the concentration of "20 Units/mL" is selected, the Order Name for this mixture should
be:exampalin (Learnix) 5,000 Units in dextrose 5% 250 mL (20 units/mL) infusionIf they choose
"40 Units/mL," the name should change to match. Assume that the EXAMPALIN 100 UNITS/ML
IJ SOLN and the DEXTROSE 5 % IV SOLN are already configured appropriately. What settings in
the MIXTURE record would you make to get the name to appear as described? - Answers -
Mixture suffix: "infusion"
Order Entry and After Ordering naming extension: 4083492101 - IP RXNAME DOSE WITH BASE,
STRENGTH, AND TOTAL VOLUME
2|Page
