ELECTRICAL CERTIFICATION TEST
EXAMINATION TEST PAPER 2026 FULL
QUESTIONS AND ANSWERS VERIFIED STUDY
GUIDE FINAL PREP 400
◉ The length of bare copper in a ground ring MUST be buried no
less that 2.5' below grade and with a length of at LEAST:
Answer: 20 feet
◉ What connector should be used to splice a 15 KV shielded cable?
Answer: Compression
◉ A 10-inch offset at 30 degrees is being made. What is the distance
between center-to-center bends?
Answer: 20 inches
◉ What is the MINIMUM length pull box that can be placed in a 2
inch conduit run where the conductors will be pulled straight?
Answer: 16 inches
◉ In hazardous locations where metal conduit is required, the
conduit MUST be threaded with what type of threads?
,Answer: Standard threads
◉ Which type of conductor is approved for instillation in a wet
location?
Answer: THHW
◉ The device used to prevent moisture from accumulating in
hazardous wet locations is called what?
Answer: A drain seal
◉ Damaged tools or extension cords should be ____?
Answer: Removed immediately from use and tagged "Do Not Use"
◉ Indoor switchgear MUST be stored in a location that protect it
from what?
Answer: Moisture
◉ What is a classified location where combustible fibers may be
present?
Answer: Class 111, Div 1
◉ What should be done if a drill motor breaks during instillation?
Answer: Tag the drill and give it to the supervisor
, ◉ The volt amperes in an AC circuit is the same as what?
Answer: Apparent power
◉ Which plan indicates the location of structures and equipment on
a property?
Answer: Site
◉ What is the standard size system used in the United States?
Answer: AWG
◉ A "megger" will be used to check a cable. The electrician MUST be
sure that the circuit is what?
Answer: De-energized & locked tagged out and tested
◉ In the event of an emergency where the lockout/tagout device is
left secured, who can remove the lockout/tagout device?
Answer: Authorized Supervisor
◉ A Type "X" conduit body has how many conduit entries
Answer: 4
EXAMINATION TEST PAPER 2026 FULL
QUESTIONS AND ANSWERS VERIFIED STUDY
GUIDE FINAL PREP 400
◉ The length of bare copper in a ground ring MUST be buried no
less that 2.5' below grade and with a length of at LEAST:
Answer: 20 feet
◉ What connector should be used to splice a 15 KV shielded cable?
Answer: Compression
◉ A 10-inch offset at 30 degrees is being made. What is the distance
between center-to-center bends?
Answer: 20 inches
◉ What is the MINIMUM length pull box that can be placed in a 2
inch conduit run where the conductors will be pulled straight?
Answer: 16 inches
◉ In hazardous locations where metal conduit is required, the
conduit MUST be threaded with what type of threads?
,Answer: Standard threads
◉ Which type of conductor is approved for instillation in a wet
location?
Answer: THHW
◉ The device used to prevent moisture from accumulating in
hazardous wet locations is called what?
Answer: A drain seal
◉ Damaged tools or extension cords should be ____?
Answer: Removed immediately from use and tagged "Do Not Use"
◉ Indoor switchgear MUST be stored in a location that protect it
from what?
Answer: Moisture
◉ What is a classified location where combustible fibers may be
present?
Answer: Class 111, Div 1
◉ What should be done if a drill motor breaks during instillation?
Answer: Tag the drill and give it to the supervisor
, ◉ The volt amperes in an AC circuit is the same as what?
Answer: Apparent power
◉ Which plan indicates the location of structures and equipment on
a property?
Answer: Site
◉ What is the standard size system used in the United States?
Answer: AWG
◉ A "megger" will be used to check a cable. The electrician MUST be
sure that the circuit is what?
Answer: De-energized & locked tagged out and tested
◉ In the event of an emergency where the lockout/tagout device is
left secured, who can remove the lockout/tagout device?
Answer: Authorized Supervisor
◉ A Type "X" conduit body has how many conduit entries
Answer: 4
