Question 1
After a long drive red fluid is seen on the transmission case and under the chassis of a
vehicle. Technician A says this can be caused by fluid aeration. Technician B says this could
be caused by engine overheating. Who is correct?
A. Technician A
B. Technician B
C. Both A and B
D. Neither A or B
CORRECT ANSWER
C. Both A and B
Question 2
The MIL is illuminated and the transmission only operates in third and reverse gears.
Which of the following is the MOST likely cause of this condition?
A. Adaptive learning.
B. High line pressure.
C. Low line pressure.
D. Limp-in mode.
CORRECT ANSWER
D. Limp-in mode.
1
@THE STUDY VAULT
,Question 3
Which of the following affects a transmission's shift points in relation to vehicle speed?
A. The throttle valve.
B. The governor.
C. Both of these.
D. Neither of these.
CORRECT ANSWER
B. The governor
Question 4
While testing the TCM of an electronic automatic transmission the technician should use
at least a:
A. 1 Megohm tester.
B. 5 Megohm tester.
C. 10 Megohm tester.
D. 20 Megohm tester.
CORRECT ANSWER
C. 10 Megohm tester.
Question 5
An automatic transaxle slips only while turning corners. Which of the following has caused
this condition?
2
@THE STUDY VAULT
, A. Worn Band
B. Torque Converter Clutch
C. Low Fluid Level
D. Planetary Gearset
CORRECT ANSWER
C. Low Fluid Level
Question 6
Refer to the chart above. Which gear ratio best represents overdrive?
A. 4.027:1
B. 0.852:1
C. 3.064:1
D. None of these.
CORRECT ANSWER
Answer B is correct. This ratio (0.852:1) represents overdrive
Question 7
A final drive assembly has been replaced. Technician A says to use an inch pound torque
wrench to check for proper pinion preload. Technician B says to use a dial indicator to
check the ring gear's backlash. Who is correct?
A. Technician A
B. Technician B
C. Both A and B
D. Neither A or B
3
@THE STUDY VAULT
After a long drive red fluid is seen on the transmission case and under the chassis of a
vehicle. Technician A says this can be caused by fluid aeration. Technician B says this could
be caused by engine overheating. Who is correct?
A. Technician A
B. Technician B
C. Both A and B
D. Neither A or B
CORRECT ANSWER
C. Both A and B
Question 2
The MIL is illuminated and the transmission only operates in third and reverse gears.
Which of the following is the MOST likely cause of this condition?
A. Adaptive learning.
B. High line pressure.
C. Low line pressure.
D. Limp-in mode.
CORRECT ANSWER
D. Limp-in mode.
1
@THE STUDY VAULT
,Question 3
Which of the following affects a transmission's shift points in relation to vehicle speed?
A. The throttle valve.
B. The governor.
C. Both of these.
D. Neither of these.
CORRECT ANSWER
B. The governor
Question 4
While testing the TCM of an electronic automatic transmission the technician should use
at least a:
A. 1 Megohm tester.
B. 5 Megohm tester.
C. 10 Megohm tester.
D. 20 Megohm tester.
CORRECT ANSWER
C. 10 Megohm tester.
Question 5
An automatic transaxle slips only while turning corners. Which of the following has caused
this condition?
2
@THE STUDY VAULT
, A. Worn Band
B. Torque Converter Clutch
C. Low Fluid Level
D. Planetary Gearset
CORRECT ANSWER
C. Low Fluid Level
Question 6
Refer to the chart above. Which gear ratio best represents overdrive?
A. 4.027:1
B. 0.852:1
C. 3.064:1
D. None of these.
CORRECT ANSWER
Answer B is correct. This ratio (0.852:1) represents overdrive
Question 7
A final drive assembly has been replaced. Technician A says to use an inch pound torque
wrench to check for proper pinion preload. Technician B says to use a dial indicator to
check the ring gear's backlash. Who is correct?
A. Technician A
B. Technician B
C. Both A and B
D. Neither A or B
3
@THE STUDY VAULT
