Jumpmaster Actual Test Paper Questions And Answers Set A.pd

JUMPMASTER ACTUAL TEST PAPER QUESTIONS
AND ANSWERS SET A+
✔✔Items with a Rated Capacity of 4,200 pounds - ✔✔-Connector Snap (Cadium Plated
Forged Steel Alloy)

✔✔Items with a Rated Capacity of 5,000 pounds - ✔✔-D Ring (Cadium Plated Forged
Steel Alloy)

✔✔Items with a Tensile Strength of 5,500 pounds - ✔✔-Risers (Type VII Nylon
Webbing)
-Harness Assembly (Primarily Type VII Nylon Webbing)
-Chest Strap (Type VII Nylon Webbing)
-Saddle (Type VII Nylon Webbing)
-Leg Straps (Type VII Nylon Webbing)
-Diagonal Backstrap (Two Plies of Type VII Nylon Webbing)
-Horizontal Backstrap (Type VII Nylon Webbing)

✔✔Items with a Tensile Strength of 6,000 pounds - ✔✔-Main Lift Web (Type VII Nylon
Webbing and Type VIII Nylon Webbing)
-Waistband Adjuster Panel (Type VII Nylon Webbing)

✔✔What does the JM Team do prior to conducting SAT? - ✔✔Inspect helmets, ID Tags,
ID Cards, and perform a technical inspection of the jumper's combat equipment when
applicable.

✔✔Three Phases of SAT? - ✔✔-Actions in the Aircraft Brief (SERJT/E) and Mock Door
Training
-Pre-Jump Training
-Parachute Landing Falls (PLF's)

✔✔What does SERJT/E stand for? - ✔✔-Static Line Control
-Exiting Procedures
-Red Light Procedures

,-Jump Refusals
-Towed Jumper Procedures
-Emergency Procedures

✔✔Ground Evacuation Alarm - ✔✔1 Continuous Ring of the Alarm Bell

✔✔Crash Landing/Ditching Alarm - ✔✔6 Short Rings of the Alarm Bell

✔✔Bailout Alarm - ✔✔3 Short Rings of the Alarm Bell followed by One Long Continuous
Ring or Verbal Warning

✔✔How many times can the JM Team exit jumpers from the mock doors? - ✔✔As many
times as they feel is necessary.

✔✔How many times must jumpers exit from the mock doors? - ✔✔At least twice, with
the last exit being conducted as planned for the airborne operation.

✔✔When should SAT be conducted? - ✔✔No earlier than 48 hours before take off.

✔✔What are the two Pre-Jump formations? - ✔✔-Extended Rectangular Formation
-Horseshoe Formation

✔✔What height should the PLF platform be at a minimum? - ✔✔24 inches

✔✔ACH Sizes - ✔✔-Small
-Medium
-Large
-Extra Large

✔✔Three Major Components of the ACH - ✔✔-Helmet Shell
-Suspension Pad System
-Modified Chinstrap Assembly

✔✔Two Authorized Suspension Pad Sizes - ✔✔-Size 6
-Size 8

✔✔How thick are size 6 suspension pads? - ✔✔3/4 inch

✔✔How thick are size 8 suspension pads? - ✔✔1 inch

✔✔Modular Airborne Weapons Case Sizes - ✔✔-Small
-Large

, ✔✔Small MAWC Width and Length - ✔✔Width: 14 inches (top) tapered to 7 inches
(bottom)
Length: 43.5 inches adjustable to 34.5 inches

✔✔Small MAWC Maximum Internal Weight Capacity - ✔✔65 pounds

✔✔Weapons Accommodated by Small MAWC - ✔✔-M4/M16 Series Rifle
-M249 SAW

✔✔Large MAWC Width and Length - ✔✔Width: 16 inches (top) tapered to 11 inches
(bottom)
Length: 52.5 inches adjustable to 41 inches

✔✔Large MAWC Maximum Internal Weight Capacity - ✔✔85 pounds

✔✔Weapons Accommodated by Large MAWC - ✔✔-M240 MG
-60mm Mortar
-Sniper Rifles

✔✔Can an M240 MG be placed inside of a Small MAWC? - ✔✔Yes, if the barrel is
removed.

✔✔Length of Hook Pile Tape Lowering Line - ✔✔15 feet

✔✔Where are the first set of hook and pile tabs on the Modified Hook Pile Tape
Lowering Line? - ✔✔46 to 48 inches from the ejector snap

✔✔Where is the blue strata mark on the Modified Hook Pile Tape Lowering Line? -
✔✔16 to 18 inches from the ejector snap

✔✔Items with a Tensile Strength of 3,600 pounds - ✔✔-Harness Single Point Release
(Type VIII Nylon Webbing)

✔✔Items with a Tensile Strength of 4,000 pounds - ✔✔-Hook Pile Tape Lowering Line
(1 inch wide Tubular Nylon Webbing)

✔✔T-10 Cargo Parachute Minimum Weight - ✔✔90 pounds

✔✔T-10 Cargo Parachute Maximum Weight - ✔✔500 pounds

✔✔T-10 Cargo Parachute Recommended Training Weight - ✔✔350 pounds

✔✔Two Types of Containers - ✔✔-A-7A Cargo Sling
-A-21 Cargo Bag