STSC STUDY EXAMS GUIDE QUESTIONS AND
ANSWERS SET A+
✔✔The FIRST step in emergency management planning is to: - ✔✔Identify and
evaluate potential disasters
✔✔The MOST important reason for investigating mishaps is - ✔✔To prevent future
occurrences
✔✔The PRIMARY consideration when preparing for a potential disaster is - ✔✔Doing
an advanced emergency planning
✔✔The PRIMARY consideration in storing chemicals is - ✔✔Segregation
✔✔A container for gasoline should be: - ✔✔Metal with UL specified non-spill cap
✔✔Personal Protective Equipment (PPE) is crucial during welding and cutting
operations. Which of the following statements is MOST correct concerning the proper
shade of filter lens to use during welding and cutting operations? - ✔✔The proper shade
of filter lens should be matched to the type of welding and cutting operation
✔✔The tree types of scheduled safety inspections are - ✔✔periodic, intermittent,
general
✔✔A bench grinder should have the tool rest adjusted to within_____inch of the wheel,
and the tongue guard should be adjusted to within_____inch of the wheel - ✔✔tool rest
within 1/8 inch of the grinding wheel, and 1/4 inch of the wheel
✔✔Proper procedure for inspection of chains during a semi-annual inspection is to -
✔✔Perform a detailed link-by-link inspection of entire chain
, ✔✔Level "B" Personal Protective Equipment (PPE) is defined as - ✔✔Chemical-
resistant suit with Self Contained Breathing Apparatus (SCBA) or Supplied Air (SA) with
escape provisions
✔✔Which is the BEST example of a fall protection method? - ✔✔Full body harness and
lifeline attached to secure anchorage that limits the fall distance
✔✔During a heatstroke, which symptom(s) would a worker UNLIKELY experience
(severe headache, profuse sweating and cool moist skin, loss of consciousness, rapid
temperature rises and hot dry skin) - ✔✔Profuse sweating and cool moist skin
✔✔Employers should perform safety inspections - ✔✔Frequently and regularly
✔✔A safety inspector observes the back of a rough terrain forklift tip is a heavy load is
being lifted on a job site. The best course of action is... - ✔✔do not continue with this lift
✔✔Minimally, all guardrail systems shall be capable of withstanding, without failure, a
force of at least _____pounds applied within 2 inches (5.1 cm) of the top edge, in any
outward or downward direction, at any point along the top edge. - ✔✔200 pounds [29
CFR 1926.502(b)]
✔✔The Primary reason for accident investigation for Safety and Health issues are -
✔✔To determine facts surrounding the event
✔✔A worker arrives on site with own PPE. Who is responsible to ensure the PPE is
appropriate for the job? - ✔✔Employer
✔✔Which of the following are the two categories used to identify respiratory protection?
- ✔✔air purifying or air supplying
✔✔A modern management approach to the success of a long-term safety management
system is known as... - ✔✔Team-based
✔✔The horizontal distance from base to vertical plane of support in straight ladder
placement should be approximately __________ the ladder length between supports. -
✔✔1/4
✔✔A worker arrives at work with his own sunglasses stating they are "safe enough",
Supervisor should look for: - ✔✔Markings for ANSI Z87 on frame (and lens)
✔✔A skin cancer caused by sunlight exposure is call - ✔✔Melanoma
ANSWERS SET A+
✔✔The FIRST step in emergency management planning is to: - ✔✔Identify and
evaluate potential disasters
✔✔The MOST important reason for investigating mishaps is - ✔✔To prevent future
occurrences
✔✔The PRIMARY consideration when preparing for a potential disaster is - ✔✔Doing
an advanced emergency planning
✔✔The PRIMARY consideration in storing chemicals is - ✔✔Segregation
✔✔A container for gasoline should be: - ✔✔Metal with UL specified non-spill cap
✔✔Personal Protective Equipment (PPE) is crucial during welding and cutting
operations. Which of the following statements is MOST correct concerning the proper
shade of filter lens to use during welding and cutting operations? - ✔✔The proper shade
of filter lens should be matched to the type of welding and cutting operation
✔✔The tree types of scheduled safety inspections are - ✔✔periodic, intermittent,
general
✔✔A bench grinder should have the tool rest adjusted to within_____inch of the wheel,
and the tongue guard should be adjusted to within_____inch of the wheel - ✔✔tool rest
within 1/8 inch of the grinding wheel, and 1/4 inch of the wheel
✔✔Proper procedure for inspection of chains during a semi-annual inspection is to -
✔✔Perform a detailed link-by-link inspection of entire chain
, ✔✔Level "B" Personal Protective Equipment (PPE) is defined as - ✔✔Chemical-
resistant suit with Self Contained Breathing Apparatus (SCBA) or Supplied Air (SA) with
escape provisions
✔✔Which is the BEST example of a fall protection method? - ✔✔Full body harness and
lifeline attached to secure anchorage that limits the fall distance
✔✔During a heatstroke, which symptom(s) would a worker UNLIKELY experience
(severe headache, profuse sweating and cool moist skin, loss of consciousness, rapid
temperature rises and hot dry skin) - ✔✔Profuse sweating and cool moist skin
✔✔Employers should perform safety inspections - ✔✔Frequently and regularly
✔✔A safety inspector observes the back of a rough terrain forklift tip is a heavy load is
being lifted on a job site. The best course of action is... - ✔✔do not continue with this lift
✔✔Minimally, all guardrail systems shall be capable of withstanding, without failure, a
force of at least _____pounds applied within 2 inches (5.1 cm) of the top edge, in any
outward or downward direction, at any point along the top edge. - ✔✔200 pounds [29
CFR 1926.502(b)]
✔✔The Primary reason for accident investigation for Safety and Health issues are -
✔✔To determine facts surrounding the event
✔✔A worker arrives on site with own PPE. Who is responsible to ensure the PPE is
appropriate for the job? - ✔✔Employer
✔✔Which of the following are the two categories used to identify respiratory protection?
- ✔✔air purifying or air supplying
✔✔A modern management approach to the success of a long-term safety management
system is known as... - ✔✔Team-based
✔✔The horizontal distance from base to vertical plane of support in straight ladder
placement should be approximately __________ the ladder length between supports. -
✔✔1/4
✔✔A worker arrives at work with his own sunglasses stating they are "safe enough",
Supervisor should look for: - ✔✔Markings for ANSI Z87 on frame (and lens)
✔✔A skin cancer caused by sunlight exposure is call - ✔✔Melanoma
