Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
1. What is the time constant for a circuit with .3 seconds
150KOhms and a 2 microfarad capacitor?
2. What must be done before checking pump drive Pull the main disconnect switch
belts on a hydraulic elevator
3. Which of the following best describes the dan- It run close by in the opposite di-
ger posed be the counterweight assembly when rection
you are riding the car top?
4. Why must you place a hydraulic elevator car on Because a hydraulic elevator is
jack posts before servicing the packing head? supported by a column of oil.
5. Why can't Elevator Constructors use a metal lad- Metal ladders conduct electricity
der?
6. What is the function of a Ground Fault Circuit To detect and imbalance in current
Interrupter? between the hot and nuetral wires
7. How do you determine the correct angle from Measure out a distance of 1/4 the
the vertical for placing a ladder height.
8. Who is required to furnish you the necessary Your employer
safety equipment?
9. What device must be in working condition in The governor and safeties.
order to use an elevator car sling as a running
platform
10. What hazardous condition can occur if the Traction could be lost
weight of the temporary car and counterweight
are not kept nearly equal?
11.
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
What is the name of the document that lists the Material Safety Data Sheet or Safety
hazards of a substance? Data Sheet
12. Who is responsible for making sure barricades Everyone on the job
are kept in place?
13. Who is primarily responsible for your safety on You, Yourself
the job?
14. Which agency guarantees your right to a safe OSHA
workplace?
15. Which of the following is not a typical elevator
repair?
16. Which of the following makes a good substitute Never substitute anything
for a ladder?
17. How should you proceed to et a toolbox to the Climb the ladder and pull the box
machine room when climbing a vertical ladder? up with a rope
18. What is the safest way to lubricate hoist ropes? With a rope lubricator
19. What supports a hydraulic elevator? The column of oil inside the jack
20. What is the first thing you must do before per- Place barricades at the upper and
forming any service on an elevator lower ends
21. When a roller bearing needs to be pressed onto Negative allowance
a shaft, what type of allowance does the shaft
have?
22. How are threads specified on metric bolts?
23. +- 1/64
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
What is the tolerance accepted in the elevator
industry?
24. What type of locking device uses a second nut
run up against the first which flattens when
tightened?
25. How many possible views are there available
from drawings using orthographic projections?
26. Best Describe Layout Drawings A mechanical drawing showing
plans and elevation views of the el-
evator installation
27. What document provides information on the Job Abstract
number of doors for an installation and their
color?
28. What is the purpose of the elevation view found To show vertical locations and di-
in the final layouts? mensions of elevator components.
29. The floor heights for the Wilton Towers are as 159' 5"
follows; sub-basement- 10'2"; subbasement to
basement-12'5"; basement to lobby-22'8"; lobby
to the 11th floor-120'5"; and to the executive
floor-16'5". What is the total travel for an eleva-
tor that travels from ht ebasement floor level to
the executive floor level?
30. DBG at the top-7' 11 5/32"
DBG at the bottom- 7' 10 17/64"
What is the difference?
31. 58%
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
You have been tasked with unloading 177 boxes
from the company truck and moving them into
a storage area. By noon you have moved 103
boxes. What percentage of the load has been
moved?
32. The counterweight must weigh 40% of the car 5100lbs
capacity plus the weight of the assembled car. If
the assembled car weighs 3800 lbs. and has a ca-
pacity of 2500lbs. what must the counterweight
weigh?
33. What is the most important piece of equipment Safety Glasses
you have when using a power saw?
34. When using a circular saw... The base is not adjustable for cut-
ting depth.
35. What functions can load weighing transducer Adjust door times, bypass hall calls,
perform and adjust motor control
36. What prevents manila rope from unraveling? Whipping
37. When using U-bolts... Place all U-bolt clips with the U
shaped portion bearing on the
dead-end of the rope
38. Capstans should be fastened to building steel or other
building structure.
39. To interrupt hoisting on a capstan... ease off on the pulling rope
40. What type of wrench is used to align the holes Spud Wrench
for rail installation?
Study online at https://quizlet.com/_7n4anh
1. What is the time constant for a circuit with .3 seconds
150KOhms and a 2 microfarad capacitor?
2. What must be done before checking pump drive Pull the main disconnect switch
belts on a hydraulic elevator
3. Which of the following best describes the dan- It run close by in the opposite di-
ger posed be the counterweight assembly when rection
you are riding the car top?
4. Why must you place a hydraulic elevator car on Because a hydraulic elevator is
jack posts before servicing the packing head? supported by a column of oil.
5. Why can't Elevator Constructors use a metal lad- Metal ladders conduct electricity
der?
6. What is the function of a Ground Fault Circuit To detect and imbalance in current
Interrupter? between the hot and nuetral wires
7. How do you determine the correct angle from Measure out a distance of 1/4 the
the vertical for placing a ladder height.
8. Who is required to furnish you the necessary Your employer
safety equipment?
9. What device must be in working condition in The governor and safeties.
order to use an elevator car sling as a running
platform
10. What hazardous condition can occur if the Traction could be lost
weight of the temporary car and counterweight
are not kept nearly equal?
11.
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
What is the name of the document that lists the Material Safety Data Sheet or Safety
hazards of a substance? Data Sheet
12. Who is responsible for making sure barricades Everyone on the job
are kept in place?
13. Who is primarily responsible for your safety on You, Yourself
the job?
14. Which agency guarantees your right to a safe OSHA
workplace?
15. Which of the following is not a typical elevator
repair?
16. Which of the following makes a good substitute Never substitute anything
for a ladder?
17. How should you proceed to et a toolbox to the Climb the ladder and pull the box
machine room when climbing a vertical ladder? up with a rope
18. What is the safest way to lubricate hoist ropes? With a rope lubricator
19. What supports a hydraulic elevator? The column of oil inside the jack
20. What is the first thing you must do before per- Place barricades at the upper and
forming any service on an elevator lower ends
21. When a roller bearing needs to be pressed onto Negative allowance
a shaft, what type of allowance does the shaft
have?
22. How are threads specified on metric bolts?
23. +- 1/64
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
What is the tolerance accepted in the elevator
industry?
24. What type of locking device uses a second nut
run up against the first which flattens when
tightened?
25. How many possible views are there available
from drawings using orthographic projections?
26. Best Describe Layout Drawings A mechanical drawing showing
plans and elevation views of the el-
evator installation
27. What document provides information on the Job Abstract
number of doors for an installation and their
color?
28. What is the purpose of the elevation view found To show vertical locations and di-
in the final layouts? mensions of elevator components.
29. The floor heights for the Wilton Towers are as 159' 5"
follows; sub-basement- 10'2"; subbasement to
basement-12'5"; basement to lobby-22'8"; lobby
to the 11th floor-120'5"; and to the executive
floor-16'5". What is the total travel for an eleva-
tor that travels from ht ebasement floor level to
the executive floor level?
30. DBG at the top-7' 11 5/32"
DBG at the bottom- 7' 10 17/64"
What is the difference?
31. 58%
, Mechanics Exam NEIEP
Study online at https://quizlet.com/_7n4anh
You have been tasked with unloading 177 boxes
from the company truck and moving them into
a storage area. By noon you have moved 103
boxes. What percentage of the load has been
moved?
32. The counterweight must weigh 40% of the car 5100lbs
capacity plus the weight of the assembled car. If
the assembled car weighs 3800 lbs. and has a ca-
pacity of 2500lbs. what must the counterweight
weigh?
33. What is the most important piece of equipment Safety Glasses
you have when using a power saw?
34. When using a circular saw... The base is not adjustable for cut-
ting depth.
35. What functions can load weighing transducer Adjust door times, bypass hall calls,
perform and adjust motor control
36. What prevents manila rope from unraveling? Whipping
37. When using U-bolts... Place all U-bolt clips with the U
shaped portion bearing on the
dead-end of the rope
38. Capstans should be fastened to building steel or other
building structure.
39. To interrupt hoisting on a capstan... ease off on the pulling rope
40. What type of wrench is used to align the holes Spud Wrench
for rail installation?
