NEIEP 200 Final EXAM COMPREHENSIVE QUESTIONS
Study online at https://quizlet.com/_jqmapy
1. NEIEP 200 Final EXAM COMPREHENSIVE QUES- NEIEP 200 Final EXAM COMPRE-
TIONS HENSIVE QUESTIONS
NEIEP 200 Final EXAM COMPREHENSIVE QUES-
TIONS
NEIEP 200 Final EXAM COMPREHENSIVE QUES-
TIONS
2. you are directed to move oxy-acetylene cylin- in an upright position
ders from a storage area to a work site. what is
the proper way to transport them?
3. you are using a plumb line to check a rail for a. the top of the rail needs to go
plumb. you find that at the top it measures 1" towards the center
and at the bottom it measures 1 1/4". what does b. the top of the rail needs to go
this tell you? toward the wall
c. the bottom of the rail needs to go
toward the wall
4. you are plumbing rails on a high rise installation. a. nylon string
what type of plumb line should you use? b. monofilament wire
c. piano wire
5. you need to cut into a concrete wall. which tool disc grinder with a diamond blade
should you use? disc
6. you need to select a heavy duty drill for drilling chuck size
5/8" holes in a machine beam. what factor de-
termines the drill rating?
, NEIEP 200 Final EXAM COMPREHENSIVE QUESTIONS
Study online at https://quizlet.com/_jqmapy
7. you are tasked with setting 3/4" concrete an- rotary hammer
chors. which type of drill should you use?
8. you need to cut and 8ft section of 1/2" EMT hacksaw with 24 teeth per inch
conduit pipe. what would be the best tool for the
job?
9. you are setting up welding equipment. what 10-12 psi
is the maximum psi that the regulator for the
acetylene gas may be adjusted to?
10. you are using rollers to move a heavy elevator angle front roller gradually and
machine and are approaching a corner. which continue around the corner
technique should you use to maneuver around
it?
11. you are preparing to unload a truck at the load- use a steel plate to span the gap
ing dock and the truck is 8" higher than the dock.
what do you do?
12. you just finished the surface inspection of a slightly untwist the strands
manila rope you will be using for hoisting. what
method should you use to conduct an internal
inspection?
13. you are preparing to hoist rails and are inspect- a light yellow color with a silvery or
ing your manila rope. which of the following is a pearly luster
good characteristic of manila rope?
14. a mechanic attaches a chainfall to a hoisting it is reduced to 50% of original ca-
beam with a beam clamp. what happens to the pacity
capacity of the hoisting beam?
Study online at https://quizlet.com/_jqmapy
1. NEIEP 200 Final EXAM COMPREHENSIVE QUES- NEIEP 200 Final EXAM COMPRE-
TIONS HENSIVE QUESTIONS
NEIEP 200 Final EXAM COMPREHENSIVE QUES-
TIONS
NEIEP 200 Final EXAM COMPREHENSIVE QUES-
TIONS
2. you are directed to move oxy-acetylene cylin- in an upright position
ders from a storage area to a work site. what is
the proper way to transport them?
3. you are using a plumb line to check a rail for a. the top of the rail needs to go
plumb. you find that at the top it measures 1" towards the center
and at the bottom it measures 1 1/4". what does b. the top of the rail needs to go
this tell you? toward the wall
c. the bottom of the rail needs to go
toward the wall
4. you are plumbing rails on a high rise installation. a. nylon string
what type of plumb line should you use? b. monofilament wire
c. piano wire
5. you need to cut into a concrete wall. which tool disc grinder with a diamond blade
should you use? disc
6. you need to select a heavy duty drill for drilling chuck size
5/8" holes in a machine beam. what factor de-
termines the drill rating?
, NEIEP 200 Final EXAM COMPREHENSIVE QUESTIONS
Study online at https://quizlet.com/_jqmapy
7. you are tasked with setting 3/4" concrete an- rotary hammer
chors. which type of drill should you use?
8. you need to cut and 8ft section of 1/2" EMT hacksaw with 24 teeth per inch
conduit pipe. what would be the best tool for the
job?
9. you are setting up welding equipment. what 10-12 psi
is the maximum psi that the regulator for the
acetylene gas may be adjusted to?
10. you are using rollers to move a heavy elevator angle front roller gradually and
machine and are approaching a corner. which continue around the corner
technique should you use to maneuver around
it?
11. you are preparing to unload a truck at the load- use a steel plate to span the gap
ing dock and the truck is 8" higher than the dock.
what do you do?
12. you just finished the surface inspection of a slightly untwist the strands
manila rope you will be using for hoisting. what
method should you use to conduct an internal
inspection?
13. you are preparing to hoist rails and are inspect- a light yellow color with a silvery or
ing your manila rope. which of the following is a pearly luster
good characteristic of manila rope?
14. a mechanic attaches a chainfall to a hoisting it is reduced to 50% of original ca-
beam with a beam clamp. what happens to the pacity
capacity of the hoisting beam?
