CWI part A TEST 100+ QUESTIONS AND CORRECT
ANSWERS 2025 LATEST//GRADED A+
Which of the following metals cannot be efficiently cut with OFC? -
(answer)stainless steel and cast iron
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Electrical conductivity of a part is the primary requirement for which NDE
method? - (answer)ET
The melting point of carbon steel is approximately? - (answer)2780
Decibel is a term associated with which NDE method? - (answer)UT
Which GMAW metal transfer mode results in the least amount of penetration? -
(answer)short circuiting
Which of the following gas(es) is commonly used as a shielding gas for GTAW? -
(answer)argon
NDE technicians are certified in accordance with? - (answer)ASNT SNT-TC-1A
When a metal is alloyed, how are the atoms of the alloy incorporated into the
original metal lattice structure? - (answer)substitutionally or interstitially
A wire is used in which NDE method? - (answer)RT
, In general, which of the following is not commonly used as a semiautomatic
process? - (answer)SMAW
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Items to be monitored by VT after welding include - (answer)Extent of welding,
final weld appearance, dimensional accuracy, amount of distortion
Crater cracks are most often the result of - (answer)improper technique
The tail of a welding symbol should not be used for - (answer)denoting groove
angle
During tempering, as the temperature increases, which of the following are
correct? - (answer)hardness decreases
In GMAW, the distance from the end of the contact tube to the arc is -
(answer)electrode extension
Of the following, which is not a type of metal transfer in GMAW - (answer)Open
Circuiting
Ultraviolet light may be used with which NDE methods? - (answer)MT and PT
, The technique which does not aid in reducing residual stress is - (answer)external
restraint
Which of the following may not be detected with VT? - (answer)Lamellar tear
Heat treatment conditions can be determined using which of the following? -
(answer)ET
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Which of the following elements are commonly used as alloying elements with
tungsten to produce GTAW electrodes - (answer)thorium
For single bevel-groove weld symbols, the line of the AWS weld symbol running
perpendicular to the reference line is always drawn on which side of the weld
symbol? - (answer)on the left
The portion of the groove fave within the joint root is called - (answer)root face
NDE technicians are usually qualified in accordance with the requirements of -
(answer)ASNT SNT-TC-1A
Which of the factors listed below has the least amount of effect on the residual
stress and distortion that results from welding? - (answer)welding position
capillary action plays a role in which NDE method - (answer)MT
ANSWERS 2025 LATEST//GRADED A+
Which of the following metals cannot be efficiently cut with OFC? -
(answer)stainless steel and cast iron
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Electrical conductivity of a part is the primary requirement for which NDE
method? - (answer)ET
The melting point of carbon steel is approximately? - (answer)2780
Decibel is a term associated with which NDE method? - (answer)UT
Which GMAW metal transfer mode results in the least amount of penetration? -
(answer)short circuiting
Which of the following gas(es) is commonly used as a shielding gas for GTAW? -
(answer)argon
NDE technicians are certified in accordance with? - (answer)ASNT SNT-TC-1A
When a metal is alloyed, how are the atoms of the alloy incorporated into the
original metal lattice structure? - (answer)substitutionally or interstitially
A wire is used in which NDE method? - (answer)RT
, In general, which of the following is not commonly used as a semiautomatic
process? - (answer)SMAW
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Items to be monitored by VT after welding include - (answer)Extent of welding,
final weld appearance, dimensional accuracy, amount of distortion
Crater cracks are most often the result of - (answer)improper technique
The tail of a welding symbol should not be used for - (answer)denoting groove
angle
During tempering, as the temperature increases, which of the following are
correct? - (answer)hardness decreases
In GMAW, the distance from the end of the contact tube to the arc is -
(answer)electrode extension
Of the following, which is not a type of metal transfer in GMAW - (answer)Open
Circuiting
Ultraviolet light may be used with which NDE methods? - (answer)MT and PT
, The technique which does not aid in reducing residual stress is - (answer)external
restraint
Which of the following may not be detected with VT? - (answer)Lamellar tear
Heat treatment conditions can be determined using which of the following? -
(answer)ET
economics, entrepreneurship, and international business.1.2. Structure of Business ExamsBusiness exams are often a mix of theoretical knowledge and practical application. Depending on the subject area, these exams
can vary significantly in format. Common types of business exams and Writing
Which of the following elements are commonly used as alloying elements with
tungsten to produce GTAW electrodes - (answer)thorium
For single bevel-groove weld symbols, the line of the AWS weld symbol running
perpendicular to the reference line is always drawn on which side of the weld
symbol? - (answer)on the left
The portion of the groove fave within the joint root is called - (answer)root face
NDE technicians are usually qualified in accordance with the requirements of -
(answer)ASNT SNT-TC-1A
Which of the factors listed below has the least amount of effect on the residual
stress and distortion that results from welding? - (answer)welding position
capillary action plays a role in which NDE method - (answer)MT
