7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
Pipefitter Star Exam AWWA (American Water
Works Association) Cross Connection Control
Specialist exam 1 |2026
Save Add to calendar
Terms in this set (800)
What causes 90% of all construction Focus Hazards
injuries and deaths and are used to
help OSHA inspectors improve their
effectiveness?
What is the minimum safe working 10 feet
distance for overhead power lines?
What is the standard procedure used Lockout/Tagout
to safely de-energize equipment on
circuits before they are worked on?
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 1/95
,7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
Which of the following is not true They can be written in any language
about Material Safety Data Sheets?
What are the four focus inspections Fall Hazards, Electrical Hazards, Caught in, Struck
OSHA compliance officers look for? by
The sizes of pipe are identified by Nominal pipe size NPS
the measurement called the:
Steel pipe is supplied with the PESC, T & C TBE
following end finish (es): (All of the above)
What is a typical type of welded pipe Butt-welded, Socket-welded, Slip-on Flanged (All
joints? of the above)
List the four principle functions of Start/Stop, Regulate/Throttle, Relief, Reduce
valves.
Regulating or throttling flow is done Both B and C, (globe and gate valve)
with a:
Name the two basic types of check Lift and Swing
valves.
The most common hanger used in Clevis
piping systems is the:
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 2/95
,7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
Never expose any part of a 125°F
compressed gas cylinder to
temperatures above:
The four types of copper tube joints compression
are soldered, brazed, flared and
_____?
What is the maximum recommended 350 degrees F
service temperature when a brazed
joint is used?
Poor alignment of tube joints will spacing difference between tubes and fittings
cause:
After fittings and tubes are cleaned as soon as possible
and fluxed they should be
assembled and soldered:
Name three basic hitches which can Straight, Choker, Basket
be used for lifting with a sling
Which hitch can support the most Basket hitch
weight?
Why should the angle between the More stress loads are applied on slings.
leg of a sling and the load never be
less than 30 degrees?
What is the weakest part of a chain Lower hook
hoist?
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 3/95
, 7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
An oxyacetylene flame has a peak 6300°F
temperature of approximately:
What is the purpose of slightly clear debris
opening/cracking a gas cylinder
valve before installing a gas
regulator?
Why is it important to ensure that no causes an explosion
part of the oxygen handling
equipment comes in contact with
oil?
What is the constant used to find the 1.414
travel with a 45 degree offset?
What is the constant used to find the .707
offset or advance with a 45o offset?
Add: 5 1/8 + 1 1/4 + 4 ½ = 10 7/8
Subtract: 9 5/8 - 6 15/16 = 2 11/16
Multiply: 3 1/5 x 1 ¼ x 1 1/3 = 5 1/3
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 4/95
Pipefitter Star Exam AWWA (American Water
Works Association) Cross Connection Control
Specialist exam 1 |2026
Save Add to calendar
Terms in this set (800)
What causes 90% of all construction Focus Hazards
injuries and deaths and are used to
help OSHA inspectors improve their
effectiveness?
What is the minimum safe working 10 feet
distance for overhead power lines?
What is the standard procedure used Lockout/Tagout
to safely de-energize equipment on
circuits before they are worked on?
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 1/95
,7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
Which of the following is not true They can be written in any language
about Material Safety Data Sheets?
What are the four focus inspections Fall Hazards, Electrical Hazards, Caught in, Struck
OSHA compliance officers look for? by
The sizes of pipe are identified by Nominal pipe size NPS
the measurement called the:
Steel pipe is supplied with the PESC, T & C TBE
following end finish (es): (All of the above)
What is a typical type of welded pipe Butt-welded, Socket-welded, Slip-on Flanged (All
joints? of the above)
List the four principle functions of Start/Stop, Regulate/Throttle, Relief, Reduce
valves.
Regulating or throttling flow is done Both B and C, (globe and gate valve)
with a:
Name the two basic types of check Lift and Swing
valves.
The most common hanger used in Clevis
piping systems is the:
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 2/95
,7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
Never expose any part of a 125°F
compressed gas cylinder to
temperatures above:
The four types of copper tube joints compression
are soldered, brazed, flared and
_____?
What is the maximum recommended 350 degrees F
service temperature when a brazed
joint is used?
Poor alignment of tube joints will spacing difference between tubes and fittings
cause:
After fittings and tubes are cleaned as soon as possible
and fluxed they should be
assembled and soldered:
Name three basic hitches which can Straight, Choker, Basket
be used for lifting with a sling
Which hitch can support the most Basket hitch
weight?
Why should the angle between the More stress loads are applied on slings.
leg of a sling and the load never be
less than 30 degrees?
What is the weakest part of a chain Lower hook
hoist?
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 3/95
, 7/13/26, 6:45 PM Pipefitter Star Exam AWWA (American Water Works Association) Cross Connection Control Specialist exam 1 |2026 Flashcards | Q…
An oxyacetylene flame has a peak 6300°F
temperature of approximately:
What is the purpose of slightly clear debris
opening/cracking a gas cylinder
valve before installing a gas
regulator?
Why is it important to ensure that no causes an explosion
part of the oxygen handling
equipment comes in contact with
oil?
What is the constant used to find the 1.414
travel with a 45 degree offset?
What is the constant used to find the .707
offset or advance with a 45o offset?
Add: 5 1/8 + 1 1/4 + 4 ½ = 10 7/8
Subtract: 9 5/8 - 6 15/16 = 2 11/16
Multiply: 3 1/5 x 1 ¼ x 1 1/3 = 5 1/3
https://quizlet.com/1194525914/pipefitter-star-exam-awwa-american-water-works-association-cross-connection-control-specialist-exam-1-2026-flash-… 4/95
