MKC SWE study GUIDE Exam Questions and
Answers with Verified Solutions | Latest
Updated 2026
Within how many days of an 10
inspection are you required to
submit the new boat inspection
report
List the six basic safety 1. Never operate, repair, adjust, tamper
procedures with
to follow when troubleshooting or equipment unless assigned to do so.
repairing electrical components 2. obey all posted operating and safety
precautions
3. de-energize equipment prior to repair.
4. always wear approved PPE.
5. use insulated tools and non-metalic
flashlight.
6. tighten the connections of fremovable
tes leads
on portable meters.
generally the crown end of the to allow for expansion and proper fit
piston is slightly smaller in
diameter
than the skirt for what reason
piston ring gaps should be 180*
staggered at _ degrees to reduce
gas leakage
,what could happen if you ignore injure yourself/people on or around the
the boat/damage outboard engine
specific safety warning in the
engine
service manual
a placard stating discharge of oil 26
prohibited must be posted on all
vessels more than __ feet in
length
what CFR regulations identifies 33CFR155.470
prohibited spaces where oil and
hazardous material are not to be
stored
what is the standard maximum 104*F
ambient operating temperature for
compressor drive motors
in the vacuum gravity system, vacuum gravity vessel
what
part houses a set of inclined
absorption plates
what filter element in an OWS is pre-filter
used
to remove small particles such as
shaving and dirt from the oily
water
mixture
, before working on or removing any the compressor is completely blown down
parts of the air compressor, you and the
should make sure the following pressure is relieved
conditions are completed
before and during the operation of make sure the flowmeters are clear and
the R/O what type of general floats are
inspection should be conducted visable
which safety precaution should be make sure all pressure relief valves
observed during R/O operation dischards are
unobstructed and the release fluid is
conducted to
low pressure area clear of personnel
what are the three effects of 1. imprecise and poor steering response
excessively worn rudder shaft 2.excessive vibration
bearings 3. leakage through the rudder post housing
what component registers Totalizing flow meter
cumulative volume in gallons of
permeate being produced by the
R/O unit and being used by the
ship
normally a diesel engine start air 1 cold and 9 hot
bank has a minimum capacity for
how
many cold and hot starts
Answers with Verified Solutions | Latest
Updated 2026
Within how many days of an 10
inspection are you required to
submit the new boat inspection
report
List the six basic safety 1. Never operate, repair, adjust, tamper
procedures with
to follow when troubleshooting or equipment unless assigned to do so.
repairing electrical components 2. obey all posted operating and safety
precautions
3. de-energize equipment prior to repair.
4. always wear approved PPE.
5. use insulated tools and non-metalic
flashlight.
6. tighten the connections of fremovable
tes leads
on portable meters.
generally the crown end of the to allow for expansion and proper fit
piston is slightly smaller in
diameter
than the skirt for what reason
piston ring gaps should be 180*
staggered at _ degrees to reduce
gas leakage
,what could happen if you ignore injure yourself/people on or around the
the boat/damage outboard engine
specific safety warning in the
engine
service manual
a placard stating discharge of oil 26
prohibited must be posted on all
vessels more than __ feet in
length
what CFR regulations identifies 33CFR155.470
prohibited spaces where oil and
hazardous material are not to be
stored
what is the standard maximum 104*F
ambient operating temperature for
compressor drive motors
in the vacuum gravity system, vacuum gravity vessel
what
part houses a set of inclined
absorption plates
what filter element in an OWS is pre-filter
used
to remove small particles such as
shaving and dirt from the oily
water
mixture
, before working on or removing any the compressor is completely blown down
parts of the air compressor, you and the
should make sure the following pressure is relieved
conditions are completed
before and during the operation of make sure the flowmeters are clear and
the R/O what type of general floats are
inspection should be conducted visable
which safety precaution should be make sure all pressure relief valves
observed during R/O operation dischards are
unobstructed and the release fluid is
conducted to
low pressure area clear of personnel
what are the three effects of 1. imprecise and poor steering response
excessively worn rudder shaft 2.excessive vibration
bearings 3. leakage through the rudder post housing
what component registers Totalizing flow meter
cumulative volume in gallons of
permeate being produced by the
R/O unit and being used by the
ship
normally a diesel engine start air 1 cold and 9 hot
bank has a minimum capacity for
how
many cold and hot starts
