Weld Inspector Level 1 Exam
( a ) Welding with damp gloves
( b ) Contact with a part of the welding circuit
( c ) Working with a broken power tool ( d ) Using a voltage decreasing device - ANS-( d ) Using
a voltage lowering device
1. Alloy steels are normally used for :
( a ) bridge girders .
( b ) pressure vessels .
( c ) tools and gears
( d ) machine castings . - ANS-( c ) tools and gears
1. An inspector is appearing as a responsible consultant of an agency while selections are :
( a ) governed by using a written list of requirements drawn up via the inspector .
( b ) primarily based on written necessities of the fabricator or manufacturer .
( c ) primarily based on the inspector's enjoy and opinions formed while examining .
( d ) shaped primarily based on session with the governing procedures and requirements . -
ANS-( d ) shaped based totally on consultation with the governing strategies and requirements .
1. Most requirements are generated by using the voluntary efforts of presidency , industry ,
clients and many others. In Canada , the country wide body that approves requirements is the :
( a ) Canadian Standards Association ( CSA )
( b ) American Bureau of Standards ( ABS )
( c ) Standards Council of Canada ( SCC )
( d ) Federal Department of Standards ( FDS ) - ANS-( c ) Standards Council of Canada ( SCC )
1. The high quality terminal of an electrical circuit is referred to as the :
( a ) work lead .
( b ) anode .
( c ) cathode .
( d ) diode - ANS-( b ) anode
1. The welding inspector's position in welding begins :
( a ) earlier than welding begins .
( b ) whilst welding is 50 % complete .
( c ) when welding is one hundred % complete and the workpiece has cooled to 50 ° C .
( d ) no sooner than forty eight hours after welding . - ANS-( a ) before welding starts offevolved
.
,1. What is the time period osed to explain an interruption of the typical shape of a fabric ?
( a ) Undercut
( b ) Defect
( c ) Discontinuity
( d ) Rejectable - ANS-( c ) Discontinuity
1. When the use of measuring gadgets , accuracy is how :
( a ) close repeated values are to each different .
( b ) many decimal factors the device has .
( c ) many readings you're taking at every dimension factor .
( d ) close repeated measurements are to the actual price . - ANS-( d ) close repeated
measurements are to the actual value .
1. Which of the subsequent is not a duty of a supervisor ?
( a ) Take each precaution affordable inside the instances to defend the people .
( b ) Provide people with written instructions for the measures and processes to be taken to
defend the people .
( c ) Ensure that employees use or wear the gadget , defensive gadgets or garb that the
corporation requires .
( d ) Prepare and implement a written health and safety program for paintings locations with
greater than 6 people . - ANS-( d ) Prepare and enforce a written fitness and safety application
for paintings locations with greater than 6 employees .
2. Engineering materials are categorized as metals and :
( a ) alloys .
( b ) non - metals .
( c ) synthetics .
( d ) herbal . - ANS-( b ) non - metals .
2. Prior to welding , the welding inspector need to test that the :
( a ) fabricator has paid the welder's and his insurance charges .
( b ) accredited welding methods are available and the welders are qualified .
( c ) material coping with system is in top working order .
( d ) welding supervisor has a welding price tag . - ANS-( b ) authorised welding processes are
to be had and the welders are certified .
2. The majority of welding - related standards in Canada are advanced with the aid of the :
( a ) Canadian Welding Association ( CWA )
( b ) Welding Institute ( TWI )
( c ) International Standards Organization ( ISO )
( d ) Canadian Standards Association ( CSA ) - ANS-( d ) Canadian Standards Association (
CSA )
,2. True of False ? To create a safe working surroundings , the business enterprise must inform
employees about the risks and provide a safe operating environment and the employee need to
use the desired protecting gadget and follow protection approaches .
( a ) True
( b ) False - ANS-(a) real
2. True or False ? Due to the type of welded structures requiring inspection , no person
magnificence of inspector is predicted to be proficient in all varieties of inspection .
( a ) True
( b ) False - ANS-( a ) True
2. True or False ? Flux cored arc welding produces a weld deposit with decrease hydrogen
ranges than gasoline tungsten arc welding .
( a ) True
( b ) False - ANS-( b ) False
2. True or False ? Systematic mistakes can usually be avoided with the aid of using a
sufficiently precise measuring device .
( a ) True
( b ) False - ANS-( b ) False
2. Which of the subsequent terms refers to an undersized fillet weld ?
( a ) Underfill
( b ) Insufficient leg
( c ) Overlap
( d ) Concave root face - ANS-( b ) Insufficient leg
three. A welding arc is intensely warm , with temperatures exceeding :
( a ) a hundred ° C .
( b ) 500 ° C .
( c ) 10,000 ° C .
( d ) 30,000 ° C . - ANS-( d ) 30,000 ° C .
Three. A welding inspector should :
( a ) have revel in as a welder .
( b ) be familiar with drawings and logos .
( c ) be an authorized Engineering Technologist .
( d ) have enjoy as a non - destructive checking out technician . - ANS-( b ) be familiar with
drawings and emblems .
Three. ASME Section IX incorporates :
( a ) design guidelines for aerospace packages .
( b ) design rules for strain vessels .
, ( c ) qualification guidelines for welding and brazing .
( d ) processes for non - detrimental testing . - ANS-( c ) qualification rules for welding and
brazing .
3. Dimensions on a drawing have to be measured from a common datum or reference line to
avoid :
( a ) comparative mistakes .
( b ) accuracy errors .
( c ) cumulative mistakes .
( d ) precision errors . - ANS-( c ) cumulative mistakes .
3. What is the difference among a single weld and a double weld ?
( a ) A unmarried weld is simplest welded from one aspect of the joint .
( b ) A single weld is made with one weld
( c ) A double weld is made with weld passes .
( d ) A double weld is only welded from one aspect of the joint . - ANS-( a ) A unmarried weld is
handiest welded from one facet of the joint .
Three. When inspecting the face of a single V - groove weld in a pipe , the quantity of weld steel
in excess of what's required to fill the joint is known as _________________
( a ) weld reinforcement
( b ) weld convexity
( c ) melt via
( d ) entire joint penetration - ANS-( a ) weld reinforcement
3. Which level of government created the Workplace Hazardous Materials Information System ,
WHMIS ?
( a ) Local
( b ) Federal
( c ) Provincial / Territorial - ANS-( b ) Federal
3. Which of the subsequent factors is used as an alloying element in metal and provides
corrosion resistance ?
( a ) Zinc
( b ) Vanadium
( c ) Magnesium
( d ) Nickel - ANS-( d ) Nickel
three. Which of the following isn't a feature of the welding inspector ?
( a ) Checking base fabric
( b ) Developing a restore technique
( c ) Checking dimensions
( d ) Witnessing warmness treating - ANS-( b ) Developing a repair technique
( a ) Welding with damp gloves
( b ) Contact with a part of the welding circuit
( c ) Working with a broken power tool ( d ) Using a voltage decreasing device - ANS-( d ) Using
a voltage lowering device
1. Alloy steels are normally used for :
( a ) bridge girders .
( b ) pressure vessels .
( c ) tools and gears
( d ) machine castings . - ANS-( c ) tools and gears
1. An inspector is appearing as a responsible consultant of an agency while selections are :
( a ) governed by using a written list of requirements drawn up via the inspector .
( b ) primarily based on written necessities of the fabricator or manufacturer .
( c ) primarily based on the inspector's enjoy and opinions formed while examining .
( d ) shaped primarily based on session with the governing procedures and requirements . -
ANS-( d ) shaped based totally on consultation with the governing strategies and requirements .
1. Most requirements are generated by using the voluntary efforts of presidency , industry ,
clients and many others. In Canada , the country wide body that approves requirements is the :
( a ) Canadian Standards Association ( CSA )
( b ) American Bureau of Standards ( ABS )
( c ) Standards Council of Canada ( SCC )
( d ) Federal Department of Standards ( FDS ) - ANS-( c ) Standards Council of Canada ( SCC )
1. The high quality terminal of an electrical circuit is referred to as the :
( a ) work lead .
( b ) anode .
( c ) cathode .
( d ) diode - ANS-( b ) anode
1. The welding inspector's position in welding begins :
( a ) earlier than welding begins .
( b ) whilst welding is 50 % complete .
( c ) when welding is one hundred % complete and the workpiece has cooled to 50 ° C .
( d ) no sooner than forty eight hours after welding . - ANS-( a ) before welding starts offevolved
.
,1. What is the time period osed to explain an interruption of the typical shape of a fabric ?
( a ) Undercut
( b ) Defect
( c ) Discontinuity
( d ) Rejectable - ANS-( c ) Discontinuity
1. When the use of measuring gadgets , accuracy is how :
( a ) close repeated values are to each different .
( b ) many decimal factors the device has .
( c ) many readings you're taking at every dimension factor .
( d ) close repeated measurements are to the actual price . - ANS-( d ) close repeated
measurements are to the actual value .
1. Which of the subsequent is not a duty of a supervisor ?
( a ) Take each precaution affordable inside the instances to defend the people .
( b ) Provide people with written instructions for the measures and processes to be taken to
defend the people .
( c ) Ensure that employees use or wear the gadget , defensive gadgets or garb that the
corporation requires .
( d ) Prepare and implement a written health and safety program for paintings locations with
greater than 6 people . - ANS-( d ) Prepare and enforce a written fitness and safety application
for paintings locations with greater than 6 employees .
2. Engineering materials are categorized as metals and :
( a ) alloys .
( b ) non - metals .
( c ) synthetics .
( d ) herbal . - ANS-( b ) non - metals .
2. Prior to welding , the welding inspector need to test that the :
( a ) fabricator has paid the welder's and his insurance charges .
( b ) accredited welding methods are available and the welders are qualified .
( c ) material coping with system is in top working order .
( d ) welding supervisor has a welding price tag . - ANS-( b ) authorised welding processes are
to be had and the welders are certified .
2. The majority of welding - related standards in Canada are advanced with the aid of the :
( a ) Canadian Welding Association ( CWA )
( b ) Welding Institute ( TWI )
( c ) International Standards Organization ( ISO )
( d ) Canadian Standards Association ( CSA ) - ANS-( d ) Canadian Standards Association (
CSA )
,2. True of False ? To create a safe working surroundings , the business enterprise must inform
employees about the risks and provide a safe operating environment and the employee need to
use the desired protecting gadget and follow protection approaches .
( a ) True
( b ) False - ANS-(a) real
2. True or False ? Due to the type of welded structures requiring inspection , no person
magnificence of inspector is predicted to be proficient in all varieties of inspection .
( a ) True
( b ) False - ANS-( a ) True
2. True or False ? Flux cored arc welding produces a weld deposit with decrease hydrogen
ranges than gasoline tungsten arc welding .
( a ) True
( b ) False - ANS-( b ) False
2. True or False ? Systematic mistakes can usually be avoided with the aid of using a
sufficiently precise measuring device .
( a ) True
( b ) False - ANS-( b ) False
2. Which of the subsequent terms refers to an undersized fillet weld ?
( a ) Underfill
( b ) Insufficient leg
( c ) Overlap
( d ) Concave root face - ANS-( b ) Insufficient leg
three. A welding arc is intensely warm , with temperatures exceeding :
( a ) a hundred ° C .
( b ) 500 ° C .
( c ) 10,000 ° C .
( d ) 30,000 ° C . - ANS-( d ) 30,000 ° C .
Three. A welding inspector should :
( a ) have revel in as a welder .
( b ) be familiar with drawings and logos .
( c ) be an authorized Engineering Technologist .
( d ) have enjoy as a non - destructive checking out technician . - ANS-( b ) be familiar with
drawings and emblems .
Three. ASME Section IX incorporates :
( a ) design guidelines for aerospace packages .
( b ) design rules for strain vessels .
, ( c ) qualification guidelines for welding and brazing .
( d ) processes for non - detrimental testing . - ANS-( c ) qualification rules for welding and
brazing .
3. Dimensions on a drawing have to be measured from a common datum or reference line to
avoid :
( a ) comparative mistakes .
( b ) accuracy errors .
( c ) cumulative mistakes .
( d ) precision errors . - ANS-( c ) cumulative mistakes .
3. What is the difference among a single weld and a double weld ?
( a ) A unmarried weld is simplest welded from one aspect of the joint .
( b ) A single weld is made with one weld
( c ) A double weld is made with weld passes .
( d ) A double weld is only welded from one aspect of the joint . - ANS-( a ) A unmarried weld is
handiest welded from one facet of the joint .
Three. When inspecting the face of a single V - groove weld in a pipe , the quantity of weld steel
in excess of what's required to fill the joint is known as _________________
( a ) weld reinforcement
( b ) weld convexity
( c ) melt via
( d ) entire joint penetration - ANS-( a ) weld reinforcement
3. Which level of government created the Workplace Hazardous Materials Information System ,
WHMIS ?
( a ) Local
( b ) Federal
( c ) Provincial / Territorial - ANS-( b ) Federal
3. Which of the subsequent factors is used as an alloying element in metal and provides
corrosion resistance ?
( a ) Zinc
( b ) Vanadium
( c ) Magnesium
( d ) Nickel - ANS-( d ) Nickel
three. Which of the following isn't a feature of the welding inspector ?
( a ) Checking base fabric
( b ) Developing a restore technique
( c ) Checking dimensions
( d ) Witnessing warmness treating - ANS-( b ) Developing a repair technique
