1. What eye protection . Is required for acetylene / oxygen
D. burning goggles
welding ?
2. How many ties are applied to a splint for a fractured
B. 2
bone ?
3. It is in the interest of the Workers Compensation Board B. Aid the worker financially and in the pursuit of rehabil-
to : itation
D. upright , properly secured and protective valve caps in
4. How must acetylene and oxygen tanks be stored ?
place
5. At 1/4 scale , an object 48 inches long will be drawn
12
inches long on the print .
6. In Figure 8 , what prevents the oil from leaking out
A. 0 - Ring seal
between the housing and the end cap ?
7. A dynamic seal is used where one of the members
D. moves
which the seal is in contact with:
8. What is the planed surface on the blade of a T - rail
D. face
called ?
9. If rails are to be stored in an elevator pit , a should
Fishplate
be attached to the bottom end of each section of rail
10. Tension of the governor rope is maintained by using
Tension sheave
a:
B. the clip is placed so that the base is on the load side of
11. What is the correct configuration for the installation of
the rope and the U bolt is placed so that it bears on the
rope clips
dead end or the short side of the rope
12. Rack and pinion machines may be used for which of
Passenger and freight
the following applications
13. What is the maximum permitted clearance from the
C. 100mm
non - access side of an enclosed vertical wheelchair lift (
, installed with min . 1067 high side walls ) to the runway
enclosure :
On a wheelchair platform , what is provided on its lower
and upper landing side to prevent roll - away of the C. A gate or safety flap
wheelchair
15. In the elevator industry , is the reporting of an accident
B. depends on the circumstances
to the Director mandatory :
16. When an accident occurs where serious injury or
B. secure the accident area to ensure nothing is disturbed
death result , which of the following procedures should
or moved until permission is given by the inspector
be implemented first :
17. Guard plates for passenger and freight elevator
D. shall extend no more than narrowest landing door
equipped with leveling or truck zoning devices shall con-
opening
form to the following except :
18. Approximately what is the rope drive sheave contact
D. 360 degrees
when double wrapping is used ?
19. After the hoistway has been plumbed and it has been
determined that the elevator will fit properly , what is the To install the rail brackets
next step in the rail installation ?
20. Brace rods are used for what purpose on the platform
C. to prevent twisting of platform
?
21. What is the main link between the hoistway walls or
A. rail brackets
building structural steel and bank the rails ?
22. Who determines where the elevator mechanic - in -
D. building contractor's superintendent
charge will store new elevator materials ?
23. How should rope tension be adjusted ? C. tightening the shackle rod nuts
24. What is the standard length of a T - rail ? D. 16 ft . ( 5m )
A. jumping
D. burning goggles
welding ?
2. How many ties are applied to a splint for a fractured
B. 2
bone ?
3. It is in the interest of the Workers Compensation Board B. Aid the worker financially and in the pursuit of rehabil-
to : itation
D. upright , properly secured and protective valve caps in
4. How must acetylene and oxygen tanks be stored ?
place
5. At 1/4 scale , an object 48 inches long will be drawn
12
inches long on the print .
6. In Figure 8 , what prevents the oil from leaking out
A. 0 - Ring seal
between the housing and the end cap ?
7. A dynamic seal is used where one of the members
D. moves
which the seal is in contact with:
8. What is the planed surface on the blade of a T - rail
D. face
called ?
9. If rails are to be stored in an elevator pit , a should
Fishplate
be attached to the bottom end of each section of rail
10. Tension of the governor rope is maintained by using
Tension sheave
a:
B. the clip is placed so that the base is on the load side of
11. What is the correct configuration for the installation of
the rope and the U bolt is placed so that it bears on the
rope clips
dead end or the short side of the rope
12. Rack and pinion machines may be used for which of
Passenger and freight
the following applications
13. What is the maximum permitted clearance from the
C. 100mm
non - access side of an enclosed vertical wheelchair lift (
, installed with min . 1067 high side walls ) to the runway
enclosure :
On a wheelchair platform , what is provided on its lower
and upper landing side to prevent roll - away of the C. A gate or safety flap
wheelchair
15. In the elevator industry , is the reporting of an accident
B. depends on the circumstances
to the Director mandatory :
16. When an accident occurs where serious injury or
B. secure the accident area to ensure nothing is disturbed
death result , which of the following procedures should
or moved until permission is given by the inspector
be implemented first :
17. Guard plates for passenger and freight elevator
D. shall extend no more than narrowest landing door
equipped with leveling or truck zoning devices shall con-
opening
form to the following except :
18. Approximately what is the rope drive sheave contact
D. 360 degrees
when double wrapping is used ?
19. After the hoistway has been plumbed and it has been
determined that the elevator will fit properly , what is the To install the rail brackets
next step in the rail installation ?
20. Brace rods are used for what purpose on the platform
C. to prevent twisting of platform
?
21. What is the main link between the hoistway walls or
A. rail brackets
building structural steel and bank the rails ?
22. Who determines where the elevator mechanic - in -
D. building contractor's superintendent
charge will store new elevator materials ?
23. How should rope tension be adjusted ? C. tightening the shackle rod nuts
24. What is the standard length of a T - rail ? D. 16 ft . ( 5m )
A. jumping
