NEIEP 200 Final 2026 Exam
Questions and Answers |
Already Graded A+
you are about to loosen a fishplate bolt. which wrench would be least
likely to slip? - ANSWER ✔✔a. 6 point box end wrench
b. 12 point box end wrench
c. open end wrench
you are using a plumb line to check a rail for plumb. you find that at the
top it measures 1" and at the bottom it measures 1 1/4". what does this
tell you? - ANSWER ✔✔a. the top of the rail needs to go towards the
center
,b. the top of the rail needs to go toward the wall
c. the bottom of the rail needs to go toward the wall
you are plumbing rails on a high rise installation. what type of plumb line
should you use? - ANSWER ✔✔a. nylon string
b. monofilament wire
c. piano wire
you need to cut into a concrete wall. which tool should you use? -
ANSWER ✔✔disc grinder with a diamond blade disc
you need to select a heavy duty drill for drilling 5/8" holes in a machine
beam. what factor determines the drill rating? - ANSWER ✔✔chuck
size
you are tasked with setting 3/4" concrete anchors. which type of drill
should you use? - ANSWER ✔✔rotary hammer
you need to cut and 8ft section of 1/2" EMT conduit pipe. what would be
the best tool for the job? - ANSWER ✔✔hacksaw with 24 teeth per
inch
, you are directed to move oxy-acetylene cylinders from a storage area to
a work site. what is the proper way to transport them? - ANSWER
✔✔in an upright position
you are setting up welding equipment. what is the maximum psi that the
regulator for the acetylene gas may be adjusted to? - ANSWER
✔✔10-12 psi
you are using rollers to move a heavy elevator machine and are
approaching a corner. which technique should you use to maneuver
around it? - ANSWER ✔✔angle front roller gradually and continue
around the corner
you are preparing to unload a truck at the loading dock and the truck is
8" higher than the dock. what do you do? - ANSWER ✔✔use a steel
plate to span the gap
you just finished the surface inspection of a manila rope you will be
using for hoisting. what method should you use to conduct an internal
inspection? - ANSWER ✔✔slightly untwist the strands
you are preparing to hoist rails and are inspecting your manila rope.
which of the following is a good characteristic of manila rope? -
ANSWER ✔✔a light yellow color with a silvery or pearly luster
COPYRIGHT©NINJANERD 2025/2026. YEAR PUBLISHED 2026. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE. PRIVACY
STATEMENT. ALL RIGHTS RESERVED
3
Questions and Answers |
Already Graded A+
you are about to loosen a fishplate bolt. which wrench would be least
likely to slip? - ANSWER ✔✔a. 6 point box end wrench
b. 12 point box end wrench
c. open end wrench
you are using a plumb line to check a rail for plumb. you find that at the
top it measures 1" and at the bottom it measures 1 1/4". what does this
tell you? - ANSWER ✔✔a. the top of the rail needs to go towards the
center
,b. the top of the rail needs to go toward the wall
c. the bottom of the rail needs to go toward the wall
you are plumbing rails on a high rise installation. what type of plumb line
should you use? - ANSWER ✔✔a. nylon string
b. monofilament wire
c. piano wire
you need to cut into a concrete wall. which tool should you use? -
ANSWER ✔✔disc grinder with a diamond blade disc
you need to select a heavy duty drill for drilling 5/8" holes in a machine
beam. what factor determines the drill rating? - ANSWER ✔✔chuck
size
you are tasked with setting 3/4" concrete anchors. which type of drill
should you use? - ANSWER ✔✔rotary hammer
you need to cut and 8ft section of 1/2" EMT conduit pipe. what would be
the best tool for the job? - ANSWER ✔✔hacksaw with 24 teeth per
inch
, you are directed to move oxy-acetylene cylinders from a storage area to
a work site. what is the proper way to transport them? - ANSWER
✔✔in an upright position
you are setting up welding equipment. what is the maximum psi that the
regulator for the acetylene gas may be adjusted to? - ANSWER
✔✔10-12 psi
you are using rollers to move a heavy elevator machine and are
approaching a corner. which technique should you use to maneuver
around it? - ANSWER ✔✔angle front roller gradually and continue
around the corner
you are preparing to unload a truck at the loading dock and the truck is
8" higher than the dock. what do you do? - ANSWER ✔✔use a steel
plate to span the gap
you just finished the surface inspection of a manila rope you will be
using for hoisting. what method should you use to conduct an internal
inspection? - ANSWER ✔✔slightly untwist the strands
you are preparing to hoist rails and are inspecting your manila rope.
which of the following is a good characteristic of manila rope? -
ANSWER ✔✔a light yellow color with a silvery or pearly luster
COPYRIGHT©NINJANERD 2025/2026. YEAR PUBLISHED 2026. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE. PRIVACY
STATEMENT. ALL RIGHTS RESERVED
3
