SE Exam (Structural
Engineering Exam)
1. A simply supported beam spans 20 ft and carries a uniform load of 2 kips/ft.
What is the maximum moment?
A. 50 kip-ft
B. 80 kip-ft
C. 100 kip-ft
D. 120 kip-ft
Answer: 100 kip-ft
Rationale: Maximum moment for a simply supported beam with uniform load is
wL²/8 = (2 × 20²)/8 = 100 kip-ft.
2. Which material property measures stiffness?
A. Yield strength
B. Ultimate strength
C. Poisson's ratio
D. Modulus of Elasticity
Answer: Modulus of Elasticity
Rationale: Modulus of Elasticity (E) measures resistance to elastic deformation
under load.
, 3. What is the primary load path in a truss?
A. Bending
B. Torsion
C. Axial forces
D. Shear
Answer: Axial forces
Rationale: Truss members are assumed to carry only tension or compression.
4. Which load is considered a transient environmental load?
A. Dead load
B. Wind load
C. Self-weight
D. Equipment load
Answer: Wind load
Rationale: Wind varies with weather conditions and is classified as an
environmental load.
5. The unit weight of normal-weight concrete is approximately:
A. 100 pcf
B. 120 pcf
C. 150 pcf
D. 200 pcf
Answer: 150 pcf
,Rationale: Standard reinforced concrete typically weighs about 150 pounds per
cubic foot.
6. The slenderness ratio of a column is:
A. A/L
B. KL/r
C. L/A
D. r/KL
Answer: KL/r
Rationale: Slenderness ratio equals effective length divided by radius of
gyration.
7. A tension member primarily resists:
A. Compression
B. Shear
C. Bending
D. Axial tension
Answer: Axial tension
Rationale: Tension members carry pulling forces along their longitudinal axis.
8. What is the SI unit of stress?
A. Newton
B. Joule
C. Pascal
D. Watt
, Answer: Pascal
Rationale: Stress equals force divided by area and is measured in Pascals.
9. Which foundation transfers load through end bearing and skin friction?
A. Spread footing
B. Mat foundation
C. Pile foundation
D. Strip footing
Answer: Pile foundation
Rationale: Piles transfer loads through friction and/or end bearing.
10.The factor of safety is generally intended to:
A. Increase loads
B. Reduce dimensions
C. Provide reserve capacity
D. Eliminate uncertainty
Answer: Provide reserve capacity
Rationale: Safety factors account for uncertainties in loads, materials, and
construction.
11.Which structural shape is most efficient in pure tension?
A. Wide flange beam
B. Channel
C. Angle
D. Rod
Engineering Exam)
1. A simply supported beam spans 20 ft and carries a uniform load of 2 kips/ft.
What is the maximum moment?
A. 50 kip-ft
B. 80 kip-ft
C. 100 kip-ft
D. 120 kip-ft
Answer: 100 kip-ft
Rationale: Maximum moment for a simply supported beam with uniform load is
wL²/8 = (2 × 20²)/8 = 100 kip-ft.
2. Which material property measures stiffness?
A. Yield strength
B. Ultimate strength
C. Poisson's ratio
D. Modulus of Elasticity
Answer: Modulus of Elasticity
Rationale: Modulus of Elasticity (E) measures resistance to elastic deformation
under load.
, 3. What is the primary load path in a truss?
A. Bending
B. Torsion
C. Axial forces
D. Shear
Answer: Axial forces
Rationale: Truss members are assumed to carry only tension or compression.
4. Which load is considered a transient environmental load?
A. Dead load
B. Wind load
C. Self-weight
D. Equipment load
Answer: Wind load
Rationale: Wind varies with weather conditions and is classified as an
environmental load.
5. The unit weight of normal-weight concrete is approximately:
A. 100 pcf
B. 120 pcf
C. 150 pcf
D. 200 pcf
Answer: 150 pcf
,Rationale: Standard reinforced concrete typically weighs about 150 pounds per
cubic foot.
6. The slenderness ratio of a column is:
A. A/L
B. KL/r
C. L/A
D. r/KL
Answer: KL/r
Rationale: Slenderness ratio equals effective length divided by radius of
gyration.
7. A tension member primarily resists:
A. Compression
B. Shear
C. Bending
D. Axial tension
Answer: Axial tension
Rationale: Tension members carry pulling forces along their longitudinal axis.
8. What is the SI unit of stress?
A. Newton
B. Joule
C. Pascal
D. Watt
, Answer: Pascal
Rationale: Stress equals force divided by area and is measured in Pascals.
9. Which foundation transfers load through end bearing and skin friction?
A. Spread footing
B. Mat foundation
C. Pile foundation
D. Strip footing
Answer: Pile foundation
Rationale: Piles transfer loads through friction and/or end bearing.
10.The factor of safety is generally intended to:
A. Increase loads
B. Reduce dimensions
C. Provide reserve capacity
D. Eliminate uncertainty
Answer: Provide reserve capacity
Rationale: Safety factors account for uncertainties in loads, materials, and
construction.
11.Which structural shape is most efficient in pure tension?
A. Wide flange beam
B. Channel
C. Angle
D. Rod