SDI Firearm Finishes and Engraving (FTT 201) Exam |
Actual Questions with Verified Answers Grade
A+ Guarantee
Save
Students also studied
Flashcard sets Study guides
Intro to Engineering Final Exam AMS 271, Recip. Engines - Unit 6 Backflow Prevention and Plumbing ... EG
Teacher 69 terms Teacher 111 terms Teacher 183 terms 44
Kithome_Jr Preview Albany_Kan Preview remo_Collins Preview
Practice questions for this set
Learn 1 /7 Study with Learn
Terms in this set (113)
T/F: One possible indicator that a barrel is likely to TRUE
shoot poorly is pitting near the crown.
Lands in the throat are which are uneven in their short Cleaning Rod Damage
points are usually caused by:
According to Joe Carlos, what must you do with a Shoot It
barrel to know for certain what its current capabilities
are?
, T/F: The electropolishing process both improves barrel FALSE
accuracy and is safe for the environment.
Joe Carlos' experiment showed that electropolishing Effective for Increasing the Accuracy of Damaged Barrels
was:
The fire lapping process involves: Firing cartridges with progressively finer grit abrasive coated bullets, which
effectively polishes the bore.
T/F: Fire lapping has about the same average effective TRUE
improvement on accuracy as electropolishing.
There is generally more need for fire lapping in: Button Rifled Bores
T/F: Fire lapping does not remove metal from the FALSE
barrel.
"Throat maintenance" bullets were found through Have a reliably positive impact on accuracy
extensive testing to:
The two basic metal preparation processes, according Hand and Machine
to Frank Fry, are:
The first of three steps to hand finishing is: Remove machine marks with files
Which of the following wheel types used in machine Felt
polishing will cut the fastest?
To prevent the loss of or "pulling" of letters and Hand
numbers, these areas should be polished by:
When using a wheel for polishing: Always polish with sharp edges pointed in the same direction the wheel is
turning.
If stamping has been damaged or pitted, you should: Leave the damaged stamping alone
Nickel plating has been a popular finish for handguns Electroplating
and certain small parts of long guns since the turn of
the century. The finish is applied by a process called:
For basic polishing: protect all of the newly-polished Light Coat of Oil
surfaces from rusting with which of the following until
you are ready to apply the bluing solution:
Actual Questions with Verified Answers Grade
A+ Guarantee
Save
Students also studied
Flashcard sets Study guides
Intro to Engineering Final Exam AMS 271, Recip. Engines - Unit 6 Backflow Prevention and Plumbing ... EG
Teacher 69 terms Teacher 111 terms Teacher 183 terms 44
Kithome_Jr Preview Albany_Kan Preview remo_Collins Preview
Practice questions for this set
Learn 1 /7 Study with Learn
Terms in this set (113)
T/F: One possible indicator that a barrel is likely to TRUE
shoot poorly is pitting near the crown.
Lands in the throat are which are uneven in their short Cleaning Rod Damage
points are usually caused by:
According to Joe Carlos, what must you do with a Shoot It
barrel to know for certain what its current capabilities
are?
, T/F: The electropolishing process both improves barrel FALSE
accuracy and is safe for the environment.
Joe Carlos' experiment showed that electropolishing Effective for Increasing the Accuracy of Damaged Barrels
was:
The fire lapping process involves: Firing cartridges with progressively finer grit abrasive coated bullets, which
effectively polishes the bore.
T/F: Fire lapping has about the same average effective TRUE
improvement on accuracy as electropolishing.
There is generally more need for fire lapping in: Button Rifled Bores
T/F: Fire lapping does not remove metal from the FALSE
barrel.
"Throat maintenance" bullets were found through Have a reliably positive impact on accuracy
extensive testing to:
The two basic metal preparation processes, according Hand and Machine
to Frank Fry, are:
The first of three steps to hand finishing is: Remove machine marks with files
Which of the following wheel types used in machine Felt
polishing will cut the fastest?
To prevent the loss of or "pulling" of letters and Hand
numbers, these areas should be polished by:
When using a wheel for polishing: Always polish with sharp edges pointed in the same direction the wheel is
turning.
If stamping has been damaged or pitted, you should: Leave the damaged stamping alone
Nickel plating has been a popular finish for handguns Electroplating
and certain small parts of long guns since the turn of
the century. The finish is applied by a process called:
For basic polishing: protect all of the newly-polished Light Coat of Oil
surfaces from rusting with which of the following until
you are ready to apply the bluing solution:
