BICSI Installer 2 Exam ACTUAL
EXAM 2026/2027 | 120 Verified
Questions Complete Review | Verified
Q&A | Pass Guaranteed - A+ Graded
Table of Contents
Section 1: Advanced Safety & Job Site Management (Questions 1–10) ...... 2
Section 2: Advanced Copper Termination & Troubleshooting (Questions 11–25) ...... 2
Section 3: Fiber Optic Advanced Handling & Testing (Questions 26–45) ...... 2
Section 4: Outside Plant (OSP) Installation (Questions 46–60) ...... 2
Section 5: Telecommunications Spaces & Support Structures (Questions 61–75) ...... 2
Section 6: Bonding & Grounding Advanced (Questions 76–90) ...... 2
Section 7: Firestopping & Inspection Requirements (Questions 91–100) ...... 2
Section 8: Testing, Documentation & Project Closeout (Questions 101–120) ...... 2
Section 1: Advanced Safety & Job Site Management
Q1: Before beginning directional boring operations near existing underground utilities, what is the
PRIMARY required action?
A. Begin boring immediately to save time
B. Contact the local one-call center (811) for utility locating and verify all marked utilities before
excavation [CORRECT]
C. Rely on as-built drawings only
D. Use only visual inspection
Correct Answer: B
Rationale: OSHA 29 CFR 1926.16 and state laws require contacting the local one-call center (dial 811) at
least 48–72 hours before excavation or directional boring to request utility locating services. All
underground utilities—including gas, electric, water, sewer, and telecommunications—must be marked
by their respective owners. Relying solely on as-built drawings or visual inspection is insufficient because
undocumented utilities, abandoned lines, and private facilities may not be shown.
,Q2: What is the PRIMARY purpose of a hot work permit?
A. To authorize overtime work
B. To document and control activities that produce sparks, flames, or heat in areas with fire hazards,
ensuring proper precautions are taken [CORRECT]
C. To approve budget expenditures
D. To schedule employee breaks
Correct Answer: B
Rationale: OSHA 29 CFR 1910.252 and NFPA 51B require hot work permits for activities such as welding,
cutting, grinding, soldering, and torch work that produce sparks, flames, or heat. The permit system
ensures that fire hazards are identified, combustible materials are removed or protected, fire
extinguishers are available, a fire watch is established, and post-work inspection confirms no smoldering
fires remain before the area is left unattended.
Q3: When working in a permit-required confined space, which role is responsible for monitoring the
entrant's safety from outside the space?
A. The supervisor
B. The attendant [CORRECT]
C. The rescue team
D. The equipment operator
Correct Answer: B
Rationale: OSHA 29 CFR 1910.146 defines the attendant as the individual stationed outside the confined
space who monitors the entrant's status, maintains communication, ensures that unauthorized persons
do not enter, and initiates rescue procedures if the entrant becomes incapacitated. The attendant must
not perform duties that distract from monitoring the entrant and must be trained in hazard recognition,
communication, and emergency procedures.
Q4: What is the PRIMARY purpose of a job hazard analysis (JHA) for lift and rigging operations?
A. To estimate material costs
B. To identify hazards associated with lifting heavy equipment, calculate load capacities, and ensure
proper rigging techniques and equipment [CORRECT]
C. To schedule employee vacations
D. To select cable colors
Correct Answer: B
Rationale: A JHA for lift and rigging operations identifies hazards including overloaded cranes or hoists,
improper sling angles, damaged rigging hardware, unstable loads, and struck-by hazards. The analysis
, ensures that load weights are calculated, rigging equipment is inspected and rated for the load, lift plans
are developed, qualified operators are assigned, and exclusion zones are established to protect
personnel from falling objects.
Q5: What is the PRIMARY safety requirement when using a personnel lift (aerial work platform) near
overhead power lines?
A. Maintain a minimum approach distance of 10 feet for lines up to 50 kV, with greater distances for
higher voltages [CORRECT]
B. Use only wooden platforms
C. No special precautions are needed
D. Work as close as possible for better access
Correct Answer: A
Rationale: OSHA 29 CFR 1910.333 and ANSI A92.2 require minimum approach distances for aerial work
platforms near energized overhead power lines: 10 feet for lines up to 50 kV, plus 0.4 inches for each
additional kV above 50 kV. Electricity can arc through air to conductive platforms, booms, and
personnel. Qualified line-clearance tree trimmers have modified requirements, but telecommunications
installers must observe standard approach distances.
Q6: What is the PRIMARY purpose of a trench box (shield) in underground cable installation?
A. To store tools
B. To protect workers from cave-ins by supporting trench walls [CORRECT]
C. To provide lighting
D. To mark the trench location
Correct Answer: B
Rationale: OSHA 29 CFR 1926.652 requires protective systems—including trench boxes (trench shields),
shoring, or sloping—for trenches deeper than 5 feet to protect workers from cave-ins. Trench boxes are
prefabricated steel or aluminum structures that are lowered into the trench and positioned around
workers to withstand soil pressure and prevent wall collapse. They do not support trench walls but
protect workers within the protected area.
Q7: What is the PRIMARY requirement for a qualified rigger under OSHA standards?
A. Any employee may serve as a rigger
B. The rigger must have documented training and experience in rigging practices, load calculations, and
hazard recognition [CORRECT]
EXAM 2026/2027 | 120 Verified
Questions Complete Review | Verified
Q&A | Pass Guaranteed - A+ Graded
Table of Contents
Section 1: Advanced Safety & Job Site Management (Questions 1–10) ...... 2
Section 2: Advanced Copper Termination & Troubleshooting (Questions 11–25) ...... 2
Section 3: Fiber Optic Advanced Handling & Testing (Questions 26–45) ...... 2
Section 4: Outside Plant (OSP) Installation (Questions 46–60) ...... 2
Section 5: Telecommunications Spaces & Support Structures (Questions 61–75) ...... 2
Section 6: Bonding & Grounding Advanced (Questions 76–90) ...... 2
Section 7: Firestopping & Inspection Requirements (Questions 91–100) ...... 2
Section 8: Testing, Documentation & Project Closeout (Questions 101–120) ...... 2
Section 1: Advanced Safety & Job Site Management
Q1: Before beginning directional boring operations near existing underground utilities, what is the
PRIMARY required action?
A. Begin boring immediately to save time
B. Contact the local one-call center (811) for utility locating and verify all marked utilities before
excavation [CORRECT]
C. Rely on as-built drawings only
D. Use only visual inspection
Correct Answer: B
Rationale: OSHA 29 CFR 1926.16 and state laws require contacting the local one-call center (dial 811) at
least 48–72 hours before excavation or directional boring to request utility locating services. All
underground utilities—including gas, electric, water, sewer, and telecommunications—must be marked
by their respective owners. Relying solely on as-built drawings or visual inspection is insufficient because
undocumented utilities, abandoned lines, and private facilities may not be shown.
,Q2: What is the PRIMARY purpose of a hot work permit?
A. To authorize overtime work
B. To document and control activities that produce sparks, flames, or heat in areas with fire hazards,
ensuring proper precautions are taken [CORRECT]
C. To approve budget expenditures
D. To schedule employee breaks
Correct Answer: B
Rationale: OSHA 29 CFR 1910.252 and NFPA 51B require hot work permits for activities such as welding,
cutting, grinding, soldering, and torch work that produce sparks, flames, or heat. The permit system
ensures that fire hazards are identified, combustible materials are removed or protected, fire
extinguishers are available, a fire watch is established, and post-work inspection confirms no smoldering
fires remain before the area is left unattended.
Q3: When working in a permit-required confined space, which role is responsible for monitoring the
entrant's safety from outside the space?
A. The supervisor
B. The attendant [CORRECT]
C. The rescue team
D. The equipment operator
Correct Answer: B
Rationale: OSHA 29 CFR 1910.146 defines the attendant as the individual stationed outside the confined
space who monitors the entrant's status, maintains communication, ensures that unauthorized persons
do not enter, and initiates rescue procedures if the entrant becomes incapacitated. The attendant must
not perform duties that distract from monitoring the entrant and must be trained in hazard recognition,
communication, and emergency procedures.
Q4: What is the PRIMARY purpose of a job hazard analysis (JHA) for lift and rigging operations?
A. To estimate material costs
B. To identify hazards associated with lifting heavy equipment, calculate load capacities, and ensure
proper rigging techniques and equipment [CORRECT]
C. To schedule employee vacations
D. To select cable colors
Correct Answer: B
Rationale: A JHA for lift and rigging operations identifies hazards including overloaded cranes or hoists,
improper sling angles, damaged rigging hardware, unstable loads, and struck-by hazards. The analysis
, ensures that load weights are calculated, rigging equipment is inspected and rated for the load, lift plans
are developed, qualified operators are assigned, and exclusion zones are established to protect
personnel from falling objects.
Q5: What is the PRIMARY safety requirement when using a personnel lift (aerial work platform) near
overhead power lines?
A. Maintain a minimum approach distance of 10 feet for lines up to 50 kV, with greater distances for
higher voltages [CORRECT]
B. Use only wooden platforms
C. No special precautions are needed
D. Work as close as possible for better access
Correct Answer: A
Rationale: OSHA 29 CFR 1910.333 and ANSI A92.2 require minimum approach distances for aerial work
platforms near energized overhead power lines: 10 feet for lines up to 50 kV, plus 0.4 inches for each
additional kV above 50 kV. Electricity can arc through air to conductive platforms, booms, and
personnel. Qualified line-clearance tree trimmers have modified requirements, but telecommunications
installers must observe standard approach distances.
Q6: What is the PRIMARY purpose of a trench box (shield) in underground cable installation?
A. To store tools
B. To protect workers from cave-ins by supporting trench walls [CORRECT]
C. To provide lighting
D. To mark the trench location
Correct Answer: B
Rationale: OSHA 29 CFR 1926.652 requires protective systems—including trench boxes (trench shields),
shoring, or sloping—for trenches deeper than 5 feet to protect workers from cave-ins. Trench boxes are
prefabricated steel or aluminum structures that are lowered into the trench and positioned around
workers to withstand soil pressure and prevent wall collapse. They do not support trench walls but
protect workers within the protected area.
Q7: What is the PRIMARY requirement for a qualified rigger under OSHA standards?
A. Any employee may serve as a rigger
B. The rigger must have documented training and experience in rigging practices, load calculations, and
hazard recognition [CORRECT]
