AMMO 64 EXAM 1 ACTUAL EXAM PAPER
2026 COMPLETE QUESTIONS AND
CORRECT ANSWERS GRADED A+
⩥ The purpose of cutting lubricant in most drilling ops is to increase the.
Answer: Drilling speed and drill bit life
⩥ Minimum protection using a bench grinder.
Answer: eye and face protection
⩥ what condition would prevent an operator from applying power to a
hoist or other powered lifting device.
Answer: an AF Form 979
⩥ most common type of lifting sling.
Answer: wire rope
⩥ the enunciators displayed on the fluke 8025 series multimeter are used
to distinguish among.
Answer: ohms, kilohm, and megohms
⩥ 2 operational modes of the Fluke 8025.
,Answer: range and hold
⩥ the steering system on the MHU 141/ M trailer has a turning radius of
how many inches.
Answer: 200
⩥ When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?.
Answer: the deck supports must be properly positioned and locked in
place with quick release pins
⩥ Max load capacity of the MHU 110/ M trailer.
Answer: 15,000
⩥ the parking brake on the MHU 110/ M is applied by.
Answer: pulling either one of two hand levers located on each side of the
front of trailer
⩥ how many openings are on the deck of the MHU- 226 trailer.
Answer: 3
⩥ what type of steering aids the MHU- 226.
Answer: four wheeled double ackerman
,⩥ After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets.
Answer: MB-1 chain assemblies and or tie down straps
⩥ what kind of movements supports on base activities to or from the
flightline.
Answer: operational
⩥ what munitions item is not loaded into transport modules by
munitions personnel.
Answer: 20 mm
⩥ what transport module used for decoy munitions has a max capacity
of 30 magazines.
Answer: ALE- 50
⩥ How often should the positive locking devices on the doors of
munitions transport modules be checked.
Answer: after loading, unloading and periodically between stops
⩥ the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to.
, Answer: provide added support and to relieve hydraulic pressure from
the lift arms when carrying loads for long distances
⩥ Lifting capacity of the MJ 1 series lift truck.
Answer: 3,000
⩥ Lifting capacity of MHU 83 lift truck.
Answer: 7,000
⩥ When using fork adapters on MHU 83 series lift truck.
Answer: it reduces lifting capacity by 1,000
⩥ What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission.
Answer: the unit coasts to a stop very quickly
⩥ what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck.
Answer: extremely slow way to build hydraulic pressure
⩥ How is the yaw positioning from the cradle or boom controls of an MJ
1 lift truck adjusted.
Answer: Manually
2026 COMPLETE QUESTIONS AND
CORRECT ANSWERS GRADED A+
⩥ The purpose of cutting lubricant in most drilling ops is to increase the.
Answer: Drilling speed and drill bit life
⩥ Minimum protection using a bench grinder.
Answer: eye and face protection
⩥ what condition would prevent an operator from applying power to a
hoist or other powered lifting device.
Answer: an AF Form 979
⩥ most common type of lifting sling.
Answer: wire rope
⩥ the enunciators displayed on the fluke 8025 series multimeter are used
to distinguish among.
Answer: ohms, kilohm, and megohms
⩥ 2 operational modes of the Fluke 8025.
,Answer: range and hold
⩥ the steering system on the MHU 141/ M trailer has a turning radius of
how many inches.
Answer: 200
⩥ When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?.
Answer: the deck supports must be properly positioned and locked in
place with quick release pins
⩥ Max load capacity of the MHU 110/ M trailer.
Answer: 15,000
⩥ the parking brake on the MHU 110/ M is applied by.
Answer: pulling either one of two hand levers located on each side of the
front of trailer
⩥ how many openings are on the deck of the MHU- 226 trailer.
Answer: 3
⩥ what type of steering aids the MHU- 226.
Answer: four wheeled double ackerman
,⩥ After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets.
Answer: MB-1 chain assemblies and or tie down straps
⩥ what kind of movements supports on base activities to or from the
flightline.
Answer: operational
⩥ what munitions item is not loaded into transport modules by
munitions personnel.
Answer: 20 mm
⩥ what transport module used for decoy munitions has a max capacity
of 30 magazines.
Answer: ALE- 50
⩥ How often should the positive locking devices on the doors of
munitions transport modules be checked.
Answer: after loading, unloading and periodically between stops
⩥ the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to.
, Answer: provide added support and to relieve hydraulic pressure from
the lift arms when carrying loads for long distances
⩥ Lifting capacity of the MJ 1 series lift truck.
Answer: 3,000
⩥ Lifting capacity of MHU 83 lift truck.
Answer: 7,000
⩥ When using fork adapters on MHU 83 series lift truck.
Answer: it reduces lifting capacity by 1,000
⩥ What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission.
Answer: the unit coasts to a stop very quickly
⩥ what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck.
Answer: extremely slow way to build hydraulic pressure
⩥ How is the yaw positioning from the cradle or boom controls of an MJ
1 lift truck adjusted.
Answer: Manually
