AUMT QUIZ 1 ACTUAL QUESTIONS AND
ANSWERS WITH COMPLETE SOLUTION | NEW
UPDATE 2026
Save
Practice questions for this set
Learn 1 /7 Study with Learn
Warpage
Choose an answer
Technician A wipes off the outside of a zerk fitting before injecting grease into it.
1 Technician B injects just enough grease to cause the boot to expand slightly. Who is
correct?
2 The petcock valve is located
3 A straightedge and feeler gauge are used to measure _____.
4 During engine warm-up, when the thermostat is closed, _____.
, Don't know?
Terms in this set (96)
Technician A wipes off the outside Both A and B
of a zerk fitting before injecting
grease into it. Technician B injects
just enough grease to cause the
boot to expand slightly. Who is
correct?
The VIN number includes all the Weight/Tire Size
information listed below EXCEPT:
When installing an oil pump in an Technician B
engine: Technician A packs the
pump with petroleum jelly.
Technician B submerges the pump
in clean oil and rotates the pump
shaft to fill the pump body. Who is
correct?
, Technician A says cooling system Technician A
pressure is regulated by the
pressure relief valve in the water
pump. Technician B says cooling
system pressure is regulated by the
radiator cap. Who is correct??
During engine warm-up, when the Coolant flows through the bypass
thermostat is closed, _____.
During routine service a small Both Technicians
amount of engine oil is found in the
air cleaner housing. Technician A
says the PCV valve may be
clogged. Technician B says the
engine could be overfilled with oil.
Who is correct?
If the fan shroud is removed from a the engine will overheat during prolonged idling
vehicle, _____.
Two technicians are discussing a Both Technicians
vehicle with an overheating
problem. There are no leaks,
internal or external. The belts are in
good condition, and the radiator
has been removed and flow tested.
Everything appears to be in good
condition. A new thermostat was
installed, but it did not cure the
problem. Technician A says the
impeller could be slipping on the
water pump shaft. Technician B says
the impeller blades could be
corroded. Who is correct?
ANSWERS WITH COMPLETE SOLUTION | NEW
UPDATE 2026
Save
Practice questions for this set
Learn 1 /7 Study with Learn
Warpage
Choose an answer
Technician A wipes off the outside of a zerk fitting before injecting grease into it.
1 Technician B injects just enough grease to cause the boot to expand slightly. Who is
correct?
2 The petcock valve is located
3 A straightedge and feeler gauge are used to measure _____.
4 During engine warm-up, when the thermostat is closed, _____.
, Don't know?
Terms in this set (96)
Technician A wipes off the outside Both A and B
of a zerk fitting before injecting
grease into it. Technician B injects
just enough grease to cause the
boot to expand slightly. Who is
correct?
The VIN number includes all the Weight/Tire Size
information listed below EXCEPT:
When installing an oil pump in an Technician B
engine: Technician A packs the
pump with petroleum jelly.
Technician B submerges the pump
in clean oil and rotates the pump
shaft to fill the pump body. Who is
correct?
, Technician A says cooling system Technician A
pressure is regulated by the
pressure relief valve in the water
pump. Technician B says cooling
system pressure is regulated by the
radiator cap. Who is correct??
During engine warm-up, when the Coolant flows through the bypass
thermostat is closed, _____.
During routine service a small Both Technicians
amount of engine oil is found in the
air cleaner housing. Technician A
says the PCV valve may be
clogged. Technician B says the
engine could be overfilled with oil.
Who is correct?
If the fan shroud is removed from a the engine will overheat during prolonged idling
vehicle, _____.
Two technicians are discussing a Both Technicians
vehicle with an overheating
problem. There are no leaks,
internal or external. The belts are in
good condition, and the radiator
has been removed and flow tested.
Everything appears to be in good
condition. A new thermostat was
installed, but it did not cure the
problem. Technician A says the
impeller could be slipping on the
water pump shaft. Technician B says
the impeller blades could be
corroded. Who is correct?
