SHARP MAIN CORE EXAMS ALL QUESTIONS AND
ANSWERS SURE A+
✔✔LSU PWB, Lens and Polygon mirror - ✔✔Which components make up the
Secondary system?
✔✔PTDL - ✔✔What is responsible for decreasing the surface voltage of the OPC drum
immediately before transfer operation?
✔✔D2PFC - ✔✔Which component controls the ON/OFF status of the Paper Feed Roller
(Paper Feed Tray 4)?
✔✔False - ✔✔When performing the Copy / Printer Gray Balance and Density
Adjustment Legal paper must be used to print the test pattern.
✔✔When DSPF section has been disassembled
When DSPF unit has been replaced
When skew appears on the image scanned from DSPF - ✔✔Under what condition
should the DSPF skew adjustment (front surface) be performed?
✔✔The Drum motor - ✔✔The developer unit is driven by which component?
, ✔✔STMPS - ✔✔What is responsible for marking each page when using the optional
Fax kit?
✔✔ - ✔✔Which components make up the Primary system?
✔✔C2LUM - ✔✔Which is responsible for lifting the paper in the Paper Feed Tray for
Feed Tray 2?
✔✔? - ✔✔Which component provides drive to the waste toner box transport screw?
✔✔TS UM
TS US - ✔✔What safety device is used to prevent overheating in the fusing unit?
Choose all that apply
✔✔False - ✔✔The Document Idle Exit Roller drives the document to the receiving tray.
✔✔False - ✔✔The D1LM drives the paper feed and transport sections. True or False
✔✔AC PWB - ✔✔The HL PWB receives power from which PWB to turn on the Heater
Lamps?
✔✔What will happen if the LCC connection is disconnected while the tray is being
lifted? - ✔✔What will happen if the LCC connection is disconnected while the tray is
being lifted?
✔✔The polarity of the voltage applied to the transfer roller is switched from positive to
negative, and unused toner on the roller is sent to the OPC drum, and cleaned by the
cleaning blade. - ✔✔How is the transfer roller cleaned?
✔✔True - ✔✔The Paper Empty Detector (C2PED, D1PED, D2PED) checks whether
there is paper in the tray when the tray is lifted and stopped at a position where it can
feed paper, as well as during paper feed operation.
✔✔True - ✔✔The paper guide stabilizes the transfer operation.
✔✔LLM - ✔✔Which motor is responsible for lifting the paper feed table to the paper
feeding position, and will lower the Paper Feed Table to allow refilling of paper when
needed?
✔✔GRID - ✔✔What pattern will be used by setting SIM 64-12 item A to a 1 for the Print
Image Distortion Manual Adj. (LSU Parallelism)?
✔✔True - ✔✔A buckle is created in the document that will ensure that the document is
squared against the registration roller.
ANSWERS SURE A+
✔✔LSU PWB, Lens and Polygon mirror - ✔✔Which components make up the
Secondary system?
✔✔PTDL - ✔✔What is responsible for decreasing the surface voltage of the OPC drum
immediately before transfer operation?
✔✔D2PFC - ✔✔Which component controls the ON/OFF status of the Paper Feed Roller
(Paper Feed Tray 4)?
✔✔False - ✔✔When performing the Copy / Printer Gray Balance and Density
Adjustment Legal paper must be used to print the test pattern.
✔✔When DSPF section has been disassembled
When DSPF unit has been replaced
When skew appears on the image scanned from DSPF - ✔✔Under what condition
should the DSPF skew adjustment (front surface) be performed?
✔✔The Drum motor - ✔✔The developer unit is driven by which component?
, ✔✔STMPS - ✔✔What is responsible for marking each page when using the optional
Fax kit?
✔✔ - ✔✔Which components make up the Primary system?
✔✔C2LUM - ✔✔Which is responsible for lifting the paper in the Paper Feed Tray for
Feed Tray 2?
✔✔? - ✔✔Which component provides drive to the waste toner box transport screw?
✔✔TS UM
TS US - ✔✔What safety device is used to prevent overheating in the fusing unit?
Choose all that apply
✔✔False - ✔✔The Document Idle Exit Roller drives the document to the receiving tray.
✔✔False - ✔✔The D1LM drives the paper feed and transport sections. True or False
✔✔AC PWB - ✔✔The HL PWB receives power from which PWB to turn on the Heater
Lamps?
✔✔What will happen if the LCC connection is disconnected while the tray is being
lifted? - ✔✔What will happen if the LCC connection is disconnected while the tray is
being lifted?
✔✔The polarity of the voltage applied to the transfer roller is switched from positive to
negative, and unused toner on the roller is sent to the OPC drum, and cleaned by the
cleaning blade. - ✔✔How is the transfer roller cleaned?
✔✔True - ✔✔The Paper Empty Detector (C2PED, D1PED, D2PED) checks whether
there is paper in the tray when the tray is lifted and stopped at a position where it can
feed paper, as well as during paper feed operation.
✔✔True - ✔✔The paper guide stabilizes the transfer operation.
✔✔LLM - ✔✔Which motor is responsible for lifting the paper feed table to the paper
feeding position, and will lower the Paper Feed Table to allow refilling of paper when
needed?
✔✔GRID - ✔✔What pattern will be used by setting SIM 64-12 item A to a 1 for the Print
Image Distortion Manual Adj. (LSU Parallelism)?
✔✔True - ✔✔A buckle is created in the document that will ensure that the document is
squared against the registration roller.
