MOT EXAM LTAP II PRACTICE TEST 2026 FULL
SOLUTIONS REVIEW PACK
◉ What is the merging taper rate minimum for a 55 mph speed
limit?
Answer: 55:1 (MT-95.40, Table II)
◉ How are portable barriers terminated?
Answer: Shall be terminated on the paved shoulder if the cross-slope
is greater than 10:1 (MT-94.40, 14a-14j)
◉ Use of cones at night shall be ________________ along tapers?
Answer: This is prohibited
◉ Drum spacing along a Two-way traffic taper shall be ______________
center to center?
Answer: 10' (MT-96.11 (a) drums/cones)
◉ What retroreflective surface should an attenuator nose (without
stripes) have?
Answer: Solid fluorescent yellow (MT-101.70)
, ◉ Spacing of a barrier reflector without a glare screen shall be
_____________?
Answer: 50' maximum center to center, Top-mounted object
markers (6"x12") at 50' maximum, Barrier reflectors and object
markers to be alternated at 25' spacing (MT-101.70)
◉ Portable barrier glare screen panels?
Answer: Glare screen delineation are vertical stripes. Vertical stripes
ae Type G, H, or J (2'x12"). They shall be placed in groups of 3, on
adjacent paddles at 50' center to center (MT-101.70)
◉ What protection is needed for a 10" drop-off in a work zone?
Answer: refer to MT-101.90 Condition 2
◉ Equip all project motor vehicles and trailers having a gross weight
of _____________ or greater in single or combination with conspicuity
tape?
Answer: 10,000 lbs (614.03 of the CMS)
◉ What type of conspicuity tape is used for vehicles over 10,000 lbs?
Answer: Use red and white, Type G, H or J retroreflective sheeting
◉ Inspection form CA-D-8 is used for what type of projects?
Answer: Long term projects
SOLUTIONS REVIEW PACK
◉ What is the merging taper rate minimum for a 55 mph speed
limit?
Answer: 55:1 (MT-95.40, Table II)
◉ How are portable barriers terminated?
Answer: Shall be terminated on the paved shoulder if the cross-slope
is greater than 10:1 (MT-94.40, 14a-14j)
◉ Use of cones at night shall be ________________ along tapers?
Answer: This is prohibited
◉ Drum spacing along a Two-way traffic taper shall be ______________
center to center?
Answer: 10' (MT-96.11 (a) drums/cones)
◉ What retroreflective surface should an attenuator nose (without
stripes) have?
Answer: Solid fluorescent yellow (MT-101.70)
, ◉ Spacing of a barrier reflector without a glare screen shall be
_____________?
Answer: 50' maximum center to center, Top-mounted object
markers (6"x12") at 50' maximum, Barrier reflectors and object
markers to be alternated at 25' spacing (MT-101.70)
◉ Portable barrier glare screen panels?
Answer: Glare screen delineation are vertical stripes. Vertical stripes
ae Type G, H, or J (2'x12"). They shall be placed in groups of 3, on
adjacent paddles at 50' center to center (MT-101.70)
◉ What protection is needed for a 10" drop-off in a work zone?
Answer: refer to MT-101.90 Condition 2
◉ Equip all project motor vehicles and trailers having a gross weight
of _____________ or greater in single or combination with conspicuity
tape?
Answer: 10,000 lbs (614.03 of the CMS)
◉ What type of conspicuity tape is used for vehicles over 10,000 lbs?
Answer: Use red and white, Type G, H or J retroreflective sheeting
◉ Inspection form CA-D-8 is used for what type of projects?
Answer: Long term projects
