NEIEP 800 Final EXAM Questions with 100% Correct
Answers | Verified || ACTUAL EXAM 2026 TEST!! Graded A+
| 2025|2026 EXAM UPDATE
Leave the first rating
Save
Students also studied
Flashcard sets Study guides
epa test NYC FDNY A-35 Air Compressor Cer... Air Assault School: Key Concepts, Ai... IPC
Teacher 100 terms Teacher 156 terms Teacher 158 terms Te
wambuimorgan Preview Tricia967 Preview ytfgvbnnjkl Preview
Practice questions for this set
Learn 1 /7 Study with Learn
What prevents the plunger from leaving the cylinder?
Choose an answer
1 Spider bob 2 Higher system pressure
3 Tail end 4 The stop ring
Don't know?
Terms in this set (90)
Hydro elevators in low rise applications do not need an overhead machine
_____ _____ room.
Some advantages of hydros are lower equipment and ground, building structure
building construction costs because the load of a
hydro is carried to the _____ where as the load of a
traction car is carried by the _____ _____.
, When drilling the jack hole, the only proper way to Spider Bob
determine if the hole is plumb is to remove the drill
stem and bit and use a _____ _____.
To plumb the hole, a spider bob is attached to a length Hoistway
of piano wire suspended from as near as possible to
the top of the _____ or from a fixed point on the drill rig.
When welding a joint, lay _____ inch tack welds _____ 1, 180
degrees apart, shift it 90 degrees and lay two more 1
inch tack welds 180 degrees apart.
On power units having the motor beneath the tank, the belt, direct
pump may be either _____ driven or _____ coupled.
The purpose of the _____/_____ is to silence the effect of silencer, muffler
any pulsations in the pump output and should be as
close to the pump as possible.
On Bolsters/Bolster Assembly, the plunger is fastened platen plate
to the _____ _____ which is then mounted to the center of
the Bolster Assembly.
With wye-delta, reduced current starting is resistors
accomplished without the need for _____.
_____ run buttons should run the platform and sling at Temporary
leveling speeds only.
A _____ _____ consists of a piston held closed by an relief valve
adjustable spring and must open at a certain pressure
to prevent any further increase in pressure.
A _____ lowering valve allows the car to be lowered at a manual
speed not exceeding 20fpm in case of power failure.
As the oil temperature changes, the _____ will change as viscosity
well and will effect the performance, more specifically,
the leveling and approach of the elevator.
Be sure wellways are properly _____ to avoid accidental barricaded
injury to you, your team or anyone working outside of
our industry.
Barricades around the wellway must be _____ inches high 42, 200
and be capable of withstanding a _____lb force.
Answers | Verified || ACTUAL EXAM 2026 TEST!! Graded A+
| 2025|2026 EXAM UPDATE
Leave the first rating
Save
Students also studied
Flashcard sets Study guides
epa test NYC FDNY A-35 Air Compressor Cer... Air Assault School: Key Concepts, Ai... IPC
Teacher 100 terms Teacher 156 terms Teacher 158 terms Te
wambuimorgan Preview Tricia967 Preview ytfgvbnnjkl Preview
Practice questions for this set
Learn 1 /7 Study with Learn
What prevents the plunger from leaving the cylinder?
Choose an answer
1 Spider bob 2 Higher system pressure
3 Tail end 4 The stop ring
Don't know?
Terms in this set (90)
Hydro elevators in low rise applications do not need an overhead machine
_____ _____ room.
Some advantages of hydros are lower equipment and ground, building structure
building construction costs because the load of a
hydro is carried to the _____ where as the load of a
traction car is carried by the _____ _____.
, When drilling the jack hole, the only proper way to Spider Bob
determine if the hole is plumb is to remove the drill
stem and bit and use a _____ _____.
To plumb the hole, a spider bob is attached to a length Hoistway
of piano wire suspended from as near as possible to
the top of the _____ or from a fixed point on the drill rig.
When welding a joint, lay _____ inch tack welds _____ 1, 180
degrees apart, shift it 90 degrees and lay two more 1
inch tack welds 180 degrees apart.
On power units having the motor beneath the tank, the belt, direct
pump may be either _____ driven or _____ coupled.
The purpose of the _____/_____ is to silence the effect of silencer, muffler
any pulsations in the pump output and should be as
close to the pump as possible.
On Bolsters/Bolster Assembly, the plunger is fastened platen plate
to the _____ _____ which is then mounted to the center of
the Bolster Assembly.
With wye-delta, reduced current starting is resistors
accomplished without the need for _____.
_____ run buttons should run the platform and sling at Temporary
leveling speeds only.
A _____ _____ consists of a piston held closed by an relief valve
adjustable spring and must open at a certain pressure
to prevent any further increase in pressure.
A _____ lowering valve allows the car to be lowered at a manual
speed not exceeding 20fpm in case of power failure.
As the oil temperature changes, the _____ will change as viscosity
well and will effect the performance, more specifically,
the leveling and approach of the elevator.
Be sure wellways are properly _____ to avoid accidental barricaded
injury to you, your team or anyone working outside of
our industry.
Barricades around the wellway must be _____ inches high 42, 200
and be capable of withstanding a _____lb force.
