NEIEP 800 Final EXAM Questions with
100% Correct Answers ACTUAL EXAM
2026
Hydro elevators in low rise applications do not need an _____ _____ room. - ANSWER -
overhead machine
Some advantages of hydros are lower equipment and building construction costs because the
load of a hydro is carried to the _____ where as the load of a traction car is carried by the
_____ _____. - ANSWER -ground, building structure
When drilling the jack hole, the only proper way to determine if the hole is plumb is to remove
the drill stem and bit and use a _____ _____. - ANSWER -Spider Bob
To plumb the hole, a spider bob is attached to a length of piano wire suspended from as near
as possible to the top of the _____ or from a fixed point on the drill rig. - ANSWER -
Hoistway
When welding a joint, lay _____ inch tack welds _____ degrees apart, shift it 90 degrees and
lay two more 1 inch tack welds 180 degrees apart. - ANSWER -1, 180
On power units having the motor beneath the tank, the pump may be either _____ driven or
_____ coupled. - ANSWER -belt, direct
, The purpose of the _____/_____ is to silence the effect of any pulsations in the pump output
and should be as close to the pump as possible. - ANSWER -silencer, muffler
On Bolsters/Bolster Assembly, the plunger is fastened to the _____ _____ which is then
mounted to the center of the Bolster Assembly. - ANSWER -platen plate
With wye-delta, reduced current starting is accomplished without the need for _____. -
ANSWER -resistors
_____ run buttons should run the platform and sling at leveling speeds only. - ANSWER -
Temporary
A _____ _____ consists of a piston held closed by an adjustable spring and must open at a
certain pressure to prevent any further increase in pressure. - ANSWER -relief valve
A _____ lowering valve allows the car to be lowered at a speed not exceeding 20fpm in case of
power failure. - ANSWER -manual
As the oil temperature changes, the _____ will change as well and will effect the performance,
more specifically, the leveling and approach of the elevator. - ANSWER -viscosity
Be sure wellways are properly _____ to avoid accidental injury to you, your team or anyone
working outside of our industry. - ANSWER -barricaded
Barricades around the wellway must be _____ inches high and be capable of withstanding a
_____lb force. - ANSWER -42, 200
A _____ protects you if you come in contact with a hot wire or component and then come in
contact with ground. It opens the circuit and diverts the supplied current to ground. -
ANSWER -GFCI
A _____ _____ is useful for horizontal (side-to-side) pulling of the truss while being lowered
into the wellway. - ANSWER -lever hoist
100% Correct Answers ACTUAL EXAM
2026
Hydro elevators in low rise applications do not need an _____ _____ room. - ANSWER -
overhead machine
Some advantages of hydros are lower equipment and building construction costs because the
load of a hydro is carried to the _____ where as the load of a traction car is carried by the
_____ _____. - ANSWER -ground, building structure
When drilling the jack hole, the only proper way to determine if the hole is plumb is to remove
the drill stem and bit and use a _____ _____. - ANSWER -Spider Bob
To plumb the hole, a spider bob is attached to a length of piano wire suspended from as near
as possible to the top of the _____ or from a fixed point on the drill rig. - ANSWER -
Hoistway
When welding a joint, lay _____ inch tack welds _____ degrees apart, shift it 90 degrees and
lay two more 1 inch tack welds 180 degrees apart. - ANSWER -1, 180
On power units having the motor beneath the tank, the pump may be either _____ driven or
_____ coupled. - ANSWER -belt, direct
, The purpose of the _____/_____ is to silence the effect of any pulsations in the pump output
and should be as close to the pump as possible. - ANSWER -silencer, muffler
On Bolsters/Bolster Assembly, the plunger is fastened to the _____ _____ which is then
mounted to the center of the Bolster Assembly. - ANSWER -platen plate
With wye-delta, reduced current starting is accomplished without the need for _____. -
ANSWER -resistors
_____ run buttons should run the platform and sling at leveling speeds only. - ANSWER -
Temporary
A _____ _____ consists of a piston held closed by an adjustable spring and must open at a
certain pressure to prevent any further increase in pressure. - ANSWER -relief valve
A _____ lowering valve allows the car to be lowered at a speed not exceeding 20fpm in case of
power failure. - ANSWER -manual
As the oil temperature changes, the _____ will change as well and will effect the performance,
more specifically, the leveling and approach of the elevator. - ANSWER -viscosity
Be sure wellways are properly _____ to avoid accidental injury to you, your team or anyone
working outside of our industry. - ANSWER -barricaded
Barricades around the wellway must be _____ inches high and be capable of withstanding a
_____lb force. - ANSWER -42, 200
A _____ protects you if you come in contact with a hot wire or component and then come in
contact with ground. It opens the circuit and diverts the supplied current to ground. -
ANSWER -GFCI
A _____ _____ is useful for horizontal (side-to-side) pulling of the truss while being lowered
into the wellway. - ANSWER -lever hoist
