NEIEP 800 final review with questions
and well verified answers actual
exam!!! 2026
The total weight of your elevator (force) is 8100 lbs. and its plunger area is 50 square inches.
What is the system pressure? - ANSWER -162 psi
Refer to the NEIEP Moving Walk Final Layout. What is the correct wellway-to-wellway
distance? - ANSWER -134' 11"
Electrolysis is caused by which of the following? - ANSWER -Stray current corrosion and
Galvanic corrosion BOTH ARE CORRECT
When using wire rope, the diameter of the sheaves must be how many times the diameter of
the suspension ropes? - ANSWER -30
Wye-Delta starting is used for which of the following? - ANSWER -Reduced current
starting
You need the area of the plunger to calculate the pressure of the hydraulic system. Your
plunger is 8 inches in diameter. What is it's area? - ANSWER -50.27 square inches
Once a plunger joint has been completed, what steps should be followed to prevent damage
to the packing? - ANSWER -Sand with emery cloth
, Under which of the following conditions will the buzzer (BZT) sound? - ANSWER -When
the handrail speed is 15% below step speed.
Refer to the NEIEP Escalator Final Layout diagram. What is the total distance from the first
floor finished floor height and the second floor finished floor height? - ANSWER -13' 6"
Refer to the NEIEP Escalator Final Layout diagram. What is the correct measurement to align
the truss in the center of the wellway? - ANSWER -7' 6 1/2"
What is the function of the lower newel wheel on a moving walk with solid balustrades? -
ANSWER -It acts as an idler
Which of the following provides mechanical interlocking of contactors? - ANSWER -
Interlock contacts
As the certified welder on the job you must weld two cylinder pieces. How must you join the
two pieces? - ANSWER -Tack welds then a fill bead
Which of the following will determine the leveling speed of an elevator? - ANSWER -Rate
of flow in gpm
Which of the following best describes the rack and pinion drive motor brake? -
ANSWER -It is spring set and electrically released
Car door switches in LULA elevators are required to operate no more than how many inches
from full closed? - - ANSWER -2"
What is the maximum rated capacity of an inclined platform lift? - ANSWER -750 Ibs..
Refer to the NEIEP Moving Walk Straight-Line Diagram. If both inspection switches (INSP sw.)
are in the downward position, how will that affect the operation of the walkway? -
ANSWER -The walkway would not run.
and well verified answers actual
exam!!! 2026
The total weight of your elevator (force) is 8100 lbs. and its plunger area is 50 square inches.
What is the system pressure? - ANSWER -162 psi
Refer to the NEIEP Moving Walk Final Layout. What is the correct wellway-to-wellway
distance? - ANSWER -134' 11"
Electrolysis is caused by which of the following? - ANSWER -Stray current corrosion and
Galvanic corrosion BOTH ARE CORRECT
When using wire rope, the diameter of the sheaves must be how many times the diameter of
the suspension ropes? - ANSWER -30
Wye-Delta starting is used for which of the following? - ANSWER -Reduced current
starting
You need the area of the plunger to calculate the pressure of the hydraulic system. Your
plunger is 8 inches in diameter. What is it's area? - ANSWER -50.27 square inches
Once a plunger joint has been completed, what steps should be followed to prevent damage
to the packing? - ANSWER -Sand with emery cloth
, Under which of the following conditions will the buzzer (BZT) sound? - ANSWER -When
the handrail speed is 15% below step speed.
Refer to the NEIEP Escalator Final Layout diagram. What is the total distance from the first
floor finished floor height and the second floor finished floor height? - ANSWER -13' 6"
Refer to the NEIEP Escalator Final Layout diagram. What is the correct measurement to align
the truss in the center of the wellway? - ANSWER -7' 6 1/2"
What is the function of the lower newel wheel on a moving walk with solid balustrades? -
ANSWER -It acts as an idler
Which of the following provides mechanical interlocking of contactors? - ANSWER -
Interlock contacts
As the certified welder on the job you must weld two cylinder pieces. How must you join the
two pieces? - ANSWER -Tack welds then a fill bead
Which of the following will determine the leveling speed of an elevator? - ANSWER -Rate
of flow in gpm
Which of the following best describes the rack and pinion drive motor brake? -
ANSWER -It is spring set and electrically released
Car door switches in LULA elevators are required to operate no more than how many inches
from full closed? - - ANSWER -2"
What is the maximum rated capacity of an inclined platform lift? - ANSWER -750 Ibs..
Refer to the NEIEP Moving Walk Straight-Line Diagram. If both inspection switches (INSP sw.)
are in the downward position, how will that affect the operation of the walkway? -
ANSWER -The walkway would not run.
