CERTIFIED SAFETY PROFESSIONAL (CSP)
PRACTICE EXAM QUESTION AND
CORRECT ANSWERS (VERIFIED
ANSWERS) PLUS RATIONALES 2026 Q&A
INSTANT DOWNLOAD PDF
1. The primary purpose of a job hazard analysis (JHA) is to:
A. Reduce employee training requirements
B. Identify hazards before they cause injury
C. Increase productivity
D. Evaluate personal performance
Rationale: A JHA systematically identifies hazards in a job before injuries
occur.
2. Which OSHA standard covers Permit-Required Confined Spaces in
Construction?
A. 1910.146
B. 1926 Subpart AA
C. 1910.120
D. 1926.501
Rationale: 1926 Subpart AA specifically addresses permit-required
confined space requirements in construction.
3. Hierarchy of controls prioritizes:
A. PPE first
B. Administrative only
C. Elimination before substitution
D. PPE before engineering controls
Rationale: The hierarchy places elimination and substitution above other
controls.
,4. The most effective way to prevent workplace injuries is:
A. PPE
B. Engineering controls
C. Safety training
D. Administrative controls
Rationale: Engineering controls remove the hazard at its source, making
them most effective.
5. A SWOT analysis assesses:
A. Safety compliance only
B. Financial risk only
C. Internal strengths, weaknesses and external opportunities, threats
D. Job classifications
Rationale: SWOT looks at strengths, weaknesses, opportunities, and
threats.
6. The LD50 of a chemical represents:
A. Lower explosion limit
B. Dose lethal to 50% of a population
C. Time to half-life
D. Minimum toxicity level
Rationale: LD50 is the dose that causes death in 50% of a test population.
7. Which of the following is a qualitative risk assessment tool?
A. Monte Carlo simulation
B. Risk matrix
C. Fault tree analysis
D. Bayesian analysis
Rationale: A risk matrix categorizes risk based on severity and likelihood
qualitatively.
8. The Safety Data Sheet (SDS) section that identifies physical and chemical
properties is:
A. Section 1
B. Section 3
C. Section 9
, D. Section 16
Rationale: Section 9 of the SDS details physical and chemical properties.
9. OSHA’s General Duty Clause is found in:
A. Section 5(b)(1)
B. Section 5(a)(1)
C. Section 6(b)(2)
D. Section 11(b)
Rationale: 5(a)(1) requires employers to provide a workplace free of
recognized hazards.
10.A BBS program focuses on:
A. Engineering design
B. Worker behaviors
C. Job descriptions
D. Regulatory requirements
Rationale: Behavior-based safety focuses on safe worker behaviors.
11.Which fire class involves combustible metals?
A. Class A
B. Class B
C. Class D
D. Class K
Rationale: Class D fires involve combustible metals.
12.The fire tetrahedron includes all but:
A. Fuel
B. Flashpoint
C. Heat
D. Oxygen
Rationale: Flashpoint is not a component of the fire tetrahedron.
13.The primary purpose of a safety committee is to:
A. Enforce discipline
B. Facilitate communication between employees and management
C. Conduct audits only
D. Handle payroll
PRACTICE EXAM QUESTION AND
CORRECT ANSWERS (VERIFIED
ANSWERS) PLUS RATIONALES 2026 Q&A
INSTANT DOWNLOAD PDF
1. The primary purpose of a job hazard analysis (JHA) is to:
A. Reduce employee training requirements
B. Identify hazards before they cause injury
C. Increase productivity
D. Evaluate personal performance
Rationale: A JHA systematically identifies hazards in a job before injuries
occur.
2. Which OSHA standard covers Permit-Required Confined Spaces in
Construction?
A. 1910.146
B. 1926 Subpart AA
C. 1910.120
D. 1926.501
Rationale: 1926 Subpart AA specifically addresses permit-required
confined space requirements in construction.
3. Hierarchy of controls prioritizes:
A. PPE first
B. Administrative only
C. Elimination before substitution
D. PPE before engineering controls
Rationale: The hierarchy places elimination and substitution above other
controls.
,4. The most effective way to prevent workplace injuries is:
A. PPE
B. Engineering controls
C. Safety training
D. Administrative controls
Rationale: Engineering controls remove the hazard at its source, making
them most effective.
5. A SWOT analysis assesses:
A. Safety compliance only
B. Financial risk only
C. Internal strengths, weaknesses and external opportunities, threats
D. Job classifications
Rationale: SWOT looks at strengths, weaknesses, opportunities, and
threats.
6. The LD50 of a chemical represents:
A. Lower explosion limit
B. Dose lethal to 50% of a population
C. Time to half-life
D. Minimum toxicity level
Rationale: LD50 is the dose that causes death in 50% of a test population.
7. Which of the following is a qualitative risk assessment tool?
A. Monte Carlo simulation
B. Risk matrix
C. Fault tree analysis
D. Bayesian analysis
Rationale: A risk matrix categorizes risk based on severity and likelihood
qualitatively.
8. The Safety Data Sheet (SDS) section that identifies physical and chemical
properties is:
A. Section 1
B. Section 3
C. Section 9
, D. Section 16
Rationale: Section 9 of the SDS details physical and chemical properties.
9. OSHA’s General Duty Clause is found in:
A. Section 5(b)(1)
B. Section 5(a)(1)
C. Section 6(b)(2)
D. Section 11(b)
Rationale: 5(a)(1) requires employers to provide a workplace free of
recognized hazards.
10.A BBS program focuses on:
A. Engineering design
B. Worker behaviors
C. Job descriptions
D. Regulatory requirements
Rationale: Behavior-based safety focuses on safe worker behaviors.
11.Which fire class involves combustible metals?
A. Class A
B. Class B
C. Class D
D. Class K
Rationale: Class D fires involve combustible metals.
12.The fire tetrahedron includes all but:
A. Fuel
B. Flashpoint
C. Heat
D. Oxygen
Rationale: Flashpoint is not a component of the fire tetrahedron.
13.The primary purpose of a safety committee is to:
A. Enforce discipline
B. Facilitate communication between employees and management
C. Conduct audits only
D. Handle payroll
