STEERING & SUSPENSION: STATE TEST
STUDY GUIDE | COMPLETE QUESTIONS
AND CORRECT DETAILED ANSWERS |
LATEST UPDATE (2026) | ALREADY
GRADED A+
Which of the following would be a typical automobile front end camber setting?
A: -4 1/2"
B: +6"
C: -3 ± 2 1/4"
D: + 1/4" - CORRECT ANSWER -D
A mechanic finds hat a front tire is worn on the inside of the tread only. The mechanic checks
the air pressure nd finds it correct. What is causing this problem?
A: The camber is set too positive
B: The camber is set too negative
C: The castor is set too positive
D: The castor is set too negative - CORRECT ANSWER -B
A car will pull to:
A: The side with the most positive (+) camber
B: The side with the most negative (-) caster
C: The side with the most positive (+) caster
,D: Both A & B - CORRECT ANSWER -D
One front tire shows spotty or isolated cupping and worn spots. What is the most likely cause of
this problem?
A: A worn stabilizer mount
B: An out-of-balance tire
C: Weak or sagging springs
D: Worn tie rod ends - CORRECT ANSWER -B
Before you remove a brake rotor from a hub, you should:
A: Unload the ball joints
B: Remove the studs
C: Mark the position of the rotor
D: Set the bearings to specifications - CORRECT ANSWER -C
The front wheels shimmy or bounce aboe 40 mph, even on a smooth, straight road. The likely
cause of this problem is:
A: Bad shocks
B: Worn strut bearings
C: Tires out of balance
D: Loose ball joints - CORRECT ANSWER -C
While replacing a ball joint, you notice that the tapered hole in the steering knuckle is oval
shaped. What should you do about this?
, A: Drill the knuckle out and install an oversized ball joint
B: Install a spacer between the new ball joint and the steering knuckle
C: Inform the customer that the knuckle should be replaced
D: Rebush the steering knuckle - CORRECT ANSWER -C
If the upper ball joints are positioned ahead of the lower ball joints, the condition is:
A: Positive caster
B: Positive camber
C: Negative caster
D: Negative camber - CORRECT ANSWER -C
What is true of most MacPherson type suspensions?
A: The lower ball joint is loaded
B: The upper ball joint is loaded
C: There are no ball joints
D: There is no upper control arm - CORRECT ANSWER -D
According to manufacturer specifications, you would adjust tapered roller front wheel bearings
so that:
A: There is zero end-play and a heavy preload
B: The spindle nut is torqued to 25 foot-pounds and then locked with a cotter pin in the next
hole clockwise
STUDY GUIDE | COMPLETE QUESTIONS
AND CORRECT DETAILED ANSWERS |
LATEST UPDATE (2026) | ALREADY
GRADED A+
Which of the following would be a typical automobile front end camber setting?
A: -4 1/2"
B: +6"
C: -3 ± 2 1/4"
D: + 1/4" - CORRECT ANSWER -D
A mechanic finds hat a front tire is worn on the inside of the tread only. The mechanic checks
the air pressure nd finds it correct. What is causing this problem?
A: The camber is set too positive
B: The camber is set too negative
C: The castor is set too positive
D: The castor is set too negative - CORRECT ANSWER -B
A car will pull to:
A: The side with the most positive (+) camber
B: The side with the most negative (-) caster
C: The side with the most positive (+) caster
,D: Both A & B - CORRECT ANSWER -D
One front tire shows spotty or isolated cupping and worn spots. What is the most likely cause of
this problem?
A: A worn stabilizer mount
B: An out-of-balance tire
C: Weak or sagging springs
D: Worn tie rod ends - CORRECT ANSWER -B
Before you remove a brake rotor from a hub, you should:
A: Unload the ball joints
B: Remove the studs
C: Mark the position of the rotor
D: Set the bearings to specifications - CORRECT ANSWER -C
The front wheels shimmy or bounce aboe 40 mph, even on a smooth, straight road. The likely
cause of this problem is:
A: Bad shocks
B: Worn strut bearings
C: Tires out of balance
D: Loose ball joints - CORRECT ANSWER -C
While replacing a ball joint, you notice that the tapered hole in the steering knuckle is oval
shaped. What should you do about this?
, A: Drill the knuckle out and install an oversized ball joint
B: Install a spacer between the new ball joint and the steering knuckle
C: Inform the customer that the knuckle should be replaced
D: Rebush the steering knuckle - CORRECT ANSWER -C
If the upper ball joints are positioned ahead of the lower ball joints, the condition is:
A: Positive caster
B: Positive camber
C: Negative caster
D: Negative camber - CORRECT ANSWER -C
What is true of most MacPherson type suspensions?
A: The lower ball joint is loaded
B: The upper ball joint is loaded
C: There are no ball joints
D: There is no upper control arm - CORRECT ANSWER -D
According to manufacturer specifications, you would adjust tapered roller front wheel bearings
so that:
A: There is zero end-play and a heavy preload
B: The spindle nut is torqued to 25 foot-pounds and then locked with a cotter pin in the next
hole clockwise
