• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 4 out of 42 pages
Exam (elaborations)

CWB Level 2 Closed Book: Comprehensive Study Guide

Document preview thumbnail
Preview 4 out of 42 pages

CWB Level 2 Closed Book: Comprehensive Study Guide

Content preview

CWB Level 2 Closed Book:
Comprehensive Study
Guide

,''The purpose of the IOI Is to verify that all defects greater than 2% of the plate
thickness have been detected." - CORRECT ANSWERSFalse
"According to CSA W59-M 1989 all backing bars must be removed prtor to
radiography." - CORRECT ANSWERSFalse
"Alloy steels and steels with greater than 0.3% carbon are fully killed." True or false? -
CORRECT ANSWERSTrue
"At about ..................... hydrogen will have NO embrittling effect." - CORRECT
ANSWERS150°C - 20°c
"Conventional flame cutting with oxy-acetylene cannot be used with stainless
steels"True or false? - CORRECT ANSWERSTrue
"Ferritic stainless steels are very tolerant of contamination during welding because of
their very high ductility" : - CORRECT ANSWERSFalse
"Good visual Inspection should always be used in conjunction with radiography. -
CORRECT ANSWERSTrue
"Hydrogen will not cause cracking in a weld unless there is stress present." True or
false? - CORRECT ANSWERSTrue
"If the fractured ends of an impact test specimen are examined, it is seen that brittle
specimens breaking with low energy have a flat crystalline fracture showing many shiny
facets." True or false? - CORRECT ANSWERSTrue
"Limestone is a fluxing agent that removes impurities to form a slag. True or false? -
CORRECT ANSWERSTrue
"Metals have a crystalline structure in which the atoms are arranged in an irregular
pattern."True or false? - CORRECT ANSWERSFalse
"One feature of hydrogen cracking is that it only occurs when the weld and heat
affected zone are at high temperatures. "True of False? - CORRECT ANSWERSFalse
"Radiography is not recommended by CSA W59 for fillet welds." - CORRECT
ANSWERSTrue
"Since radiography Is a volumetric method the condition of the surface Is not an
Important factor." - CORRECT ANSWERSFalse
"Solidified weld metal will have a microstructure the same as that of the parent material
(plate)." True or false? - CORRECT ANSWERSFalse
"Strain is the extension divided by the original length. "True or false? - CORRECT
ANSWERSTrue
"Stress is the load divided by the original cross-sectional area." True or false? -
CORRECT ANSWERSTrue
"The drop weight test is a test for the toughness of the steel and is not used for
measuring toughness of weld metal or the heat affected zone." True or false? -
CORRECT ANSWERSTrue
"The only thing that causes fuzziness at the edge of an image ts geometric
unsharpness.'' - CORRECT ANSWERSFalse, fuzziness Is also caused by inherent
unsharpness and scattering
"The risk of cracking from sulphur is even greater if the weld metal contains more than
about. ...................... of nickel." - CORRECT ANSWERS3%
"Welds in austenitic stainless steels are always preheated to prevent hydrogen induced
cracking" True or false - CORRECT ANSWERSFalse
"X-rays are a type of electromagnetic wave but y rays are beams of tiny charged

,particles." True or false? - CORRECT ANSWERSFalse
100% C02 is not generally used for GMAW of stainless steels" True or false? -
CORRECT ANSWERSTrue
A 14% Cr martensitic steel heated to 1000°c and air cooled produces - CORRECT
ANSWERSmartensite
A 60% duty cycle means that the power supply can deliver its rated output for:
A 60% of the rated output only
B. 60% over the rated output followed by 4 minutes at rest
C. 6 minutes at rest followed by 4 minutes at rated output
D. 6 minutes at rated output followed by 4 minutes at rest - CORRECT ANSWERSD. 6
minutes at rated output followed by 4 minutes at rest
A carbon steel component operates satisfactorily at 500°C under a stress of 50MPa.
If 304 stainless were substituted, up to what level could the temperature be raised? -
CORRECT ANSWERS600*C
A constant voltage power supply is required for GMAW process. - CORRECT
ANSWERSTrue
A conventional diode placed in a circuit allows the passage of current in one direction
only. A silicon controlled rectifier(SCR) operates slightly differently. How does it work?
A. an SCR conducts current in both directions until turned on and current flow is then
prevented
B. an SCR is non-conductive until turned onland then allows current to flow in both
directions
C. an SCR is non-conductive until turned on, allowing current to flow in one direction
only until the flow of current stops
D. an SCR is a unique rectifying device which allows only alternating c1:1rrent to flow
until turned off - CORRECT ANSWERSC. an SCR is non-conductive until turned on,
allowing current to flow in one direction only until the flow of current stops
A couplant Is only needed If the IUCface Is rough. - CORRECT ANSWERSFalse
A dark narrow area 2-3 mm wide appears on a radiograph all the way along the edge of
the area representing the weld. The joint was a 60° double Vee groove. What does this
dark area most likely represent? - CORRECT ANSWERSUndercut
A dark, narrow area about 2-3 mm wide appears on a radiograph of a double vee
groove weld along the edge of the area representing the weld. What does this dark area
most likely represent?
A. lack of side wall fusion
B. incomplete penetration
C. undercut
D. slag entrapment
E. weld metal crack - CORRECT ANSWERSC. undercut
A disadvantage of magnetic particle Inspection is that it Is impossible to obtain any kind
of permanent record of the indication. - CORRECT ANSWERSFalse. Photographs or
adhesive tape transfers can be used
A disadvantage of SCR control is that the output is very 'choppy'. How is the output
made more suitable for welding?
A. the output is smoothed out by the addition of capacitors
B. the large inductor or choke will be added to the circuit

, C. the output from an SCR bridge is smooth enough for welding purposes
D. the diodes added to all SCR controlled machines to prevent "choppy" output -
CORRECT ANSWERSA. the output is smoothed out by the addition of capacitor
A generator consists of rotating conductors in a stationary magnetic field and an
alternator consists of rotating magnetic field inside the conductor windings. - CORRECT
ANSWERSTrue
A guided root bend test on a weld would best reveal: - CORRECT ANSWERSlack of
penetration of fusion
A large ASTM grain size number indicates: - CORRECT ANSWERSA fine grain
A liquid that wets a surface is characterized by:
A. No capillary action
B. A small contact angle
C. High density
D. High surface tension
E. Low fluorescence - CORRECT ANSWERSB. A small contact angle
A method of controlling weld metal fissuring is - CORRECT ANSWERSto ensure there
is a small amount of residual delta ferrite in the weld metal
A radiographic indication 2 to 3 mm wide is observed running along the toe of a double
vee groove weld. Of the choices below, which one is it most likely to be?
A. Weld metal crack
B. Undercut
C. Slag inclusion
D. Lack of side wall fusion
E. Incomplete penetration - CORRECT ANSWERSB. Undercut
A radlograph of a groove weld in a 25.4 mm thick dynamically loaded tension member
shows two 6 mm pores with 50 mm between the edges of the pores along the length of
the weld. Is this acceptable to CSA W59-M1989? - CORRECT ANSWERSNo
A stainless steel deposit is made on mild steel ( 0.2%C, 1%Mn) with 50% dilution.
What should the Ni and Cr equivalents of the electrode be to avoid formation of
martensite in the deposit? - CORRECT ANSWERS18 Ni equivalent; 35 Cr equivalent.
A steel bar of square cross-section, 50 mm x 50 mm is subjected to a load of 213 kN.
What is the tensile stress in the bar? - CORRECT ANSWERS85.2 MPa
A straight chromium steel with <0.1 % carbon and 18% chromium when heated to
1000°C will- - CORRECT ANSWERSRemain ferritic
A transformer type welding power source without a rectifier outputs what type of
current?
A. direct current
B. alternating current
C. high frequency current
D. pulsed direct current - CORRECT ANSWERSB. alternating current
A well-defined line indication with tightly held, heavy powder buildup is likely to
represent
a) Porosity
b) A sub-surface crack
c) A crack open to the surface - CORRECT ANSWERSc) A crack open to the surface
According to ASTM E-165, the surface temperature for liquid penetrant inspection

Document information

Uploaded on
April 28, 2026
Number of pages
42
Written in
2025/2026
Type
Exam (elaborations)
Contains
Questions & answers
$58.99

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
Dock2
4.0
(5)
Sold
22
Followers
11
Items
3742
Last sold
2 weeks ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions