CSWA SIMULATION QUESTIONS WITH
CORRECT ANSWERS 2026
H-method of meshing involves - CORRECT ANSWER --increasing mesh density
P-method of meshingPinvolves - CORRECT ANSWER --increasing mesh element polynomial order
Is it possible to model breaking of glass on the floor using linear static analysis? -
CORRECT ANSWER --no
Which of the following cases, the rope will most likely break? - CORRECT ANSWER -
- both are the same
Assuming a linear static study, if the Young's modulus of the material is doubles (everything else
remains the same), then the tensile stress will be - CORRECT ANSWER --doubles
Iso lot in the simulation will enable to - CORRECT ANSWER --
set lower and upper limits to see desired stress range
Which statement best describes a compatible mesh? - CORRECT ANSWER -
- a mesh where elements on touching bodies have overlaying nodes
Maximum and minimum value indicators are displayed on stress and displacement plots in SOLI
DWORKS simulation for a linear static study - CORRECT ANSWER --true
What SOLIDWORKS simulation tool should you use to determine the result values at specificPloca
tions (nodes) in a model using SOLIDWORKS simulation? - CORRECT ANSWER --probe tool
, What criteria are best suited to check the failure of ductile materials in SOLIDWORKS simulation
? - CORRECT ANSWER --maximum von Mises stress and maximum shear stress criterion
What is the modulus of elasticity? - CORRECT ANSWER --the slope of the stress-
strain curve in its linear section
What is stress? - CORRECT ANSWER --
a measure of average amount of force exerted per unit area
Which of the following assumptions are true for a static analysis in SOLIDWORKS simulation with
small displacements? - CORRECT ANSWER --
1. Inertia effects are negligible and loads are applied slowly
2. All the displacements are small relative to the model geometry
3. Results are proportional to loads
What is yield stress? - CORRECT ANSWER --
the stress level beyond which the material becomes plastic
A high-quality shell element has____nodes. - CORRECT ANSWER --6
Stress is proportional to in linear elastic material. - CORRECT ANSWER --strain
The elastic modulus (Young's modulus) is the slope defined as divided by .
- CORRECT ANSWER --stress, strain
Linear staticPanalysis assumes that the relationship between loads and the induced response is: -
CORRECT ANSWER --linear
CORRECT ANSWERS 2026
H-method of meshing involves - CORRECT ANSWER --increasing mesh density
P-method of meshingPinvolves - CORRECT ANSWER --increasing mesh element polynomial order
Is it possible to model breaking of glass on the floor using linear static analysis? -
CORRECT ANSWER --no
Which of the following cases, the rope will most likely break? - CORRECT ANSWER -
- both are the same
Assuming a linear static study, if the Young's modulus of the material is doubles (everything else
remains the same), then the tensile stress will be - CORRECT ANSWER --doubles
Iso lot in the simulation will enable to - CORRECT ANSWER --
set lower and upper limits to see desired stress range
Which statement best describes a compatible mesh? - CORRECT ANSWER -
- a mesh where elements on touching bodies have overlaying nodes
Maximum and minimum value indicators are displayed on stress and displacement plots in SOLI
DWORKS simulation for a linear static study - CORRECT ANSWER --true
What SOLIDWORKS simulation tool should you use to determine the result values at specificPloca
tions (nodes) in a model using SOLIDWORKS simulation? - CORRECT ANSWER --probe tool
, What criteria are best suited to check the failure of ductile materials in SOLIDWORKS simulation
? - CORRECT ANSWER --maximum von Mises stress and maximum shear stress criterion
What is the modulus of elasticity? - CORRECT ANSWER --the slope of the stress-
strain curve in its linear section
What is stress? - CORRECT ANSWER --
a measure of average amount of force exerted per unit area
Which of the following assumptions are true for a static analysis in SOLIDWORKS simulation with
small displacements? - CORRECT ANSWER --
1. Inertia effects are negligible and loads are applied slowly
2. All the displacements are small relative to the model geometry
3. Results are proportional to loads
What is yield stress? - CORRECT ANSWER --
the stress level beyond which the material becomes plastic
A high-quality shell element has____nodes. - CORRECT ANSWER --6
Stress is proportional to in linear elastic material. - CORRECT ANSWER --strain
The elastic modulus (Young's modulus) is the slope defined as divided by .
- CORRECT ANSWER --stress, strain
Linear staticPanalysis assumes that the relationship between loads and the induced response is: -
CORRECT ANSWER --linear
