ADHESIVE ANCHOR TRAINING EXAM
QUESTIONS AND ANSWERS 2026
VERIFIED.
Minimum anchor spacing and edge distance, as well as minimum member thickness, must
comply with the values given - ANS In the products ICC-ES Report
The registered design professional in responsible charge and the engineers of record involved in
the design of the project are permitted to act as the - ANS Approved Agency
If reinforcing bars are encountered during drilling the correct action would be -
ANS Consulting with the EOR
for adhesive anchors, the characteristics bond stresses and suitability for structural applications
are established by testing in accordance with - ANS ACI 355.4
Special inspections and tests shall be required for proposal work that is, in the opinion of the
building official, unusual in its nature, as such, but not limited to - ANS All of the above
ACI 355.4, qualification of post installed adhesive anchors in concrete, is applicable to anchors
with a specified minimum embedment depth of - ANS 1 - 5/8 inches
@2026/2027 ALLRIGHTS RESERVED.
, Proof loads are usually determined as a - ANS Percentage of the anchor ultimate tensile
strength
True or False: The contractor is permitted to employ the approved agencies for special
inspection where the contractor is also the owner of the project? - ANS True
The effective embedment depth, measure from the concrete surface to the deepest point at
which bond to the concrete is established is identified as - ANS h subscript(ef)
True or false: Powers PE1000+ epoxy adhesive are recognized for use to resist short-term and
long-term loads, including wind and earthquake loads, subject to conditions of the ICC-ES
Evaluation report? - ANS True
Short sections of anchor rods the have been burned or sawed are indictive of: - ANS Incorrect
embedment
The elapsed time after mixing adhesive material components to onset of significant chemical
reaction as characterized by an increase in viscosity is - ANS Gel Time
Periodic and final inspection reports are required to be summited to the - ANS Building
official and engineer or architect of record
Powers PE1000+ epoxy adhesive anchors must be installed in accordance with? - ANS The
manufacturers published installation instructions
ACI 355.4-11 qualification of post installed adhesive anchors in concrete standard applies to
anchors with diameter of 1/4in or larger and an embedment depth not exceeding: -
ANS 20d(a)
@2026/2027 ALLRIGHTS RESERVED.
QUESTIONS AND ANSWERS 2026
VERIFIED.
Minimum anchor spacing and edge distance, as well as minimum member thickness, must
comply with the values given - ANS In the products ICC-ES Report
The registered design professional in responsible charge and the engineers of record involved in
the design of the project are permitted to act as the - ANS Approved Agency
If reinforcing bars are encountered during drilling the correct action would be -
ANS Consulting with the EOR
for adhesive anchors, the characteristics bond stresses and suitability for structural applications
are established by testing in accordance with - ANS ACI 355.4
Special inspections and tests shall be required for proposal work that is, in the opinion of the
building official, unusual in its nature, as such, but not limited to - ANS All of the above
ACI 355.4, qualification of post installed adhesive anchors in concrete, is applicable to anchors
with a specified minimum embedment depth of - ANS 1 - 5/8 inches
@2026/2027 ALLRIGHTS RESERVED.
, Proof loads are usually determined as a - ANS Percentage of the anchor ultimate tensile
strength
True or False: The contractor is permitted to employ the approved agencies for special
inspection where the contractor is also the owner of the project? - ANS True
The effective embedment depth, measure from the concrete surface to the deepest point at
which bond to the concrete is established is identified as - ANS h subscript(ef)
True or false: Powers PE1000+ epoxy adhesive are recognized for use to resist short-term and
long-term loads, including wind and earthquake loads, subject to conditions of the ICC-ES
Evaluation report? - ANS True
Short sections of anchor rods the have been burned or sawed are indictive of: - ANS Incorrect
embedment
The elapsed time after mixing adhesive material components to onset of significant chemical
reaction as characterized by an increase in viscosity is - ANS Gel Time
Periodic and final inspection reports are required to be summited to the - ANS Building
official and engineer or architect of record
Powers PE1000+ epoxy adhesive anchors must be installed in accordance with? - ANS The
manufacturers published installation instructions
ACI 355.4-11 qualification of post installed adhesive anchors in concrete standard applies to
anchors with diameter of 1/4in or larger and an embedment depth not exceeding: -
ANS 20d(a)
@2026/2027 ALLRIGHTS RESERVED.
