Solution Manual for Automotive Technology: A
Systems Approach Exam Questions and
Answers with Complete Solutions (Already
Passed A+) 2026/2027
• Box end -✓✓A wrench that completely surrounds the boat head or not
is called
• Center -✓✓What punch is used to make a small indentation in metal
before drilling a hole
• Forward stroke -✓✓When using a hacksaw, you should apply light
pressure on what stroke
• B -✓✓When working with sockets, technician A states that a sockets
point is the size of the square opening for the handle. Technician b
States the point of a socket is the box configuration for the bolthead.
Who is right
• 1000 -✓✓Insulated tools for use on hybrid vehicle drive train should
be rated at least ___V
• True -✓✓Powered for tools used in the automotive shop is provided by
compressed air, hydraulics, Electricity. True or false
• Jackstands -✓✓Used to support a vehicle after it has been raised
• Oxygen -✓✓A cutting torch generates tremendous heat by burning
acetylene gas and
• 100 to 150 psi -✓✓Shop air pressure usually ranges from
, • Flat black -✓✓Special impact sockets and extensions are easily
identified because
• False -✓✓When using gasoline soak up any spills with an oil
absorbent. True or false
• False -✓✓A magnetic pick up will attract any kind of metal. True or
false
• False -✓✓If the head of a chisel or punch becomes mushroomed, the
tool must be discarded. True or false
• False -✓✓Dead blow hammer is another name for the rubber mallet
• True -✓✓An adjustable wrench should be used only one other types of
wrenches will not fit. True or false
• False -✓✓Torque screws have a square indentation in their heads. True
or false
• True -✓✓True or false: an Allen wrench has a hexagonal
shaft
• True -✓✓True or false: the six point box and wrench should be used
when a bolt head or nut is extremely tight
• True -✓✓True or false: The tip of a pin punch should be ground flat
and square
• False -✓✓True or false: for safety, battery charger leads must be
connected to the battery after the charger is turned on
Systems Approach Exam Questions and
Answers with Complete Solutions (Already
Passed A+) 2026/2027
• Box end -✓✓A wrench that completely surrounds the boat head or not
is called
• Center -✓✓What punch is used to make a small indentation in metal
before drilling a hole
• Forward stroke -✓✓When using a hacksaw, you should apply light
pressure on what stroke
• B -✓✓When working with sockets, technician A states that a sockets
point is the size of the square opening for the handle. Technician b
States the point of a socket is the box configuration for the bolthead.
Who is right
• 1000 -✓✓Insulated tools for use on hybrid vehicle drive train should
be rated at least ___V
• True -✓✓Powered for tools used in the automotive shop is provided by
compressed air, hydraulics, Electricity. True or false
• Jackstands -✓✓Used to support a vehicle after it has been raised
• Oxygen -✓✓A cutting torch generates tremendous heat by burning
acetylene gas and
• 100 to 150 psi -✓✓Shop air pressure usually ranges from
, • Flat black -✓✓Special impact sockets and extensions are easily
identified because
• False -✓✓When using gasoline soak up any spills with an oil
absorbent. True or false
• False -✓✓A magnetic pick up will attract any kind of metal. True or
false
• False -✓✓If the head of a chisel or punch becomes mushroomed, the
tool must be discarded. True or false
• False -✓✓Dead blow hammer is another name for the rubber mallet
• True -✓✓An adjustable wrench should be used only one other types of
wrenches will not fit. True or false
• False -✓✓Torque screws have a square indentation in their heads. True
or false
• True -✓✓True or false: an Allen wrench has a hexagonal
shaft
• True -✓✓True or false: the six point box and wrench should be used
when a bolt head or nut is extremely tight
• True -✓✓True or false: The tip of a pin punch should be ground flat
and square
• False -✓✓True or false: for safety, battery charger leads must be
connected to the battery after the charger is turned on
