1|Page
FIRST CLASS STEAM LICENSE EXAM LATEST 2026-2027 ACTUAL
EXAM WITH COMPLETE QUESTIONS AND CORRECT DETAILED
ANSWERS (100% VERIFIED ANSWERS) |ALREADY GRADED A+|
||PROFESSOR VERIFIED|| ||BRANDNEW!!!||
According to the ASME Code, if the MAWP exceeds___p.s.i, the
blowdown lines and the fittings must be composed of materials
suitable for the temperature and pressures allowed - ANSWER-
125 p.s.i
A steam trap can be tested with an ___ to determine if it is
working properly - ANSWER-ultra sonic device
In large steam boiler plants, a ___ is necessary to provide the
extra capacity required to handle changing loads and peak flows
of condensate - ANSWER-surge tank
(280+psi systems)
A ___ steam trap is a steam trap that has a single movable disc
that rises to allow the discharge of air and cool condensate -
ANSWER-thermodynamic
,2|Page
Some ___ moisture separators automatically open and close
because they use a wax that expands and contracts with
temperature changes - ANSWER-variable oriface
The raw makeup water system generally has a float chamber
located at the ___ water level in a surge tank - ANSWER-
minimum
Transfer pumps are used to transfer the mixture of ___ from a
surge tank to the deaerator or directly to the boiler feedwater
pumps - ANSWER-condensate and raw makeup water
A makeup control valve is used to ___ - ANSWER-maintain a
constant water level in the feedwater heater
The.... ___ .....is the water level designated as being the proper
water level for safe boiler operation - ANSWER-N.O.W.L. ...
Normal Operating Water Level
, 3|Page
The purpose of a feedwater regulator is to........ ___ - ANSWER-
maintain a constant water level in the boiler
Feedwater regulators control the feedwater pump to maintain the
water level....... ___ - ANSWER-at the N.O.W.L
The sequence of 3 numbers found on the nameplate mounted on
a reciprocating feed-water pump refers to........ ___ - ANSWER--
diameter of the steam piston..............
-diameter of the water piston.............. and
length of the pump stroke.
___ are usually used to create the draft needed to overcome the
resistance caused by economizer tubes - ANSWER-Induced draft
fans (they pull the draft through the furnace)
An economizer uses the heat energy from the gases of
combustion leaving the boiler to heat the ............ - ANSWER-
feedwater
FIRST CLASS STEAM LICENSE EXAM LATEST 2026-2027 ACTUAL
EXAM WITH COMPLETE QUESTIONS AND CORRECT DETAILED
ANSWERS (100% VERIFIED ANSWERS) |ALREADY GRADED A+|
||PROFESSOR VERIFIED|| ||BRANDNEW!!!||
According to the ASME Code, if the MAWP exceeds___p.s.i, the
blowdown lines and the fittings must be composed of materials
suitable for the temperature and pressures allowed - ANSWER-
125 p.s.i
A steam trap can be tested with an ___ to determine if it is
working properly - ANSWER-ultra sonic device
In large steam boiler plants, a ___ is necessary to provide the
extra capacity required to handle changing loads and peak flows
of condensate - ANSWER-surge tank
(280+psi systems)
A ___ steam trap is a steam trap that has a single movable disc
that rises to allow the discharge of air and cool condensate -
ANSWER-thermodynamic
,2|Page
Some ___ moisture separators automatically open and close
because they use a wax that expands and contracts with
temperature changes - ANSWER-variable oriface
The raw makeup water system generally has a float chamber
located at the ___ water level in a surge tank - ANSWER-
minimum
Transfer pumps are used to transfer the mixture of ___ from a
surge tank to the deaerator or directly to the boiler feedwater
pumps - ANSWER-condensate and raw makeup water
A makeup control valve is used to ___ - ANSWER-maintain a
constant water level in the feedwater heater
The.... ___ .....is the water level designated as being the proper
water level for safe boiler operation - ANSWER-N.O.W.L. ...
Normal Operating Water Level
, 3|Page
The purpose of a feedwater regulator is to........ ___ - ANSWER-
maintain a constant water level in the boiler
Feedwater regulators control the feedwater pump to maintain the
water level....... ___ - ANSWER-at the N.O.W.L
The sequence of 3 numbers found on the nameplate mounted on
a reciprocating feed-water pump refers to........ ___ - ANSWER--
diameter of the steam piston..............
-diameter of the water piston.............. and
length of the pump stroke.
___ are usually used to create the draft needed to overcome the
resistance caused by economizer tubes - ANSWER-Induced draft
fans (they pull the draft through the furnace)
An economizer uses the heat energy from the gases of
combustion leaving the boiler to heat the ............ - ANSWER-
feedwater
