IPC A 610 EXAM QUESTIONS AND
ANSWERS 100% PASS 2026/2027
Class 1 Product - ANS General Electronics Product - includes products where the major
requirement is function of the completed assembly.
Class 2 Product - ANS Dedicated Service Electronic Product - Continued performance and
extended life required. Uninterrupted service is desired but not required.
Class 3 Product - ANS High Performance Electrical Product - Continued high performance or
performance-on-demand is critical. Equipment downtime cannot be tolerated. Equipment
might be used for life-support or other critical systems.
Who as the ultimate responsibility for identifying the class to which the assembly is evaluated? -
ANS The Customer.
Shall - ANS Invokes a requirement for manufacturers of all classes or product, and failure to
comply with the requirement is a noncompliance to this standard.
Order of Precedence in event of conflict 1 - ANS 1. Procurement as agreed and documented
between customer and supplier.
Order of Precedence in event of conflict 2 - ANS Master drawing or master ass. drawing
reflecting the customer's detailed requirements.
2026/2027 ALLRIGHTS RESERVED
1
, Order of Precedence in event of conflict 3 - ANS IPC-1-610 when invoked by the customer or
contract.
If documents other than IPC-A-610 are cited, the order of precedence shall be defined in the _ -
ANS Procurement documents
Target Condition - ANS A condition that is close to perfect, but is not always achievable and
may not be necessary to ensure the reliability of the assembly.
Acceptable Condition - ANS A condition that, while not necessarily perfect, will maintain
integrity and reliability of the assembly
Defect Condition - ANS The form, fit or function of the assembly is inadequate for use in its
end use environment.
A defect for Class 1... - ANS automatically implies a defect for Class 2 and 3. A defect for Class
2 implies a defect for Class 3.
Disposition - ANS The determination of how defects should be treated. These include rework,
use as is, scrap, and repair.
Who dispositions defect conditions? - ANS The manufacturer, based on design, service and
customer requirements.
Process Indicator Conditions - ANS A condition (not a defect) that does not affect the form, fit
or function of a product.
Process indicators should be... - ANS monitored as part of the process control system
Is disposition of individual process indicators required? - ANS No, and affected products
should be used as-is.
2026/2027 ALLRIGHTS RESERVED
2
ANSWERS 100% PASS 2026/2027
Class 1 Product - ANS General Electronics Product - includes products where the major
requirement is function of the completed assembly.
Class 2 Product - ANS Dedicated Service Electronic Product - Continued performance and
extended life required. Uninterrupted service is desired but not required.
Class 3 Product - ANS High Performance Electrical Product - Continued high performance or
performance-on-demand is critical. Equipment downtime cannot be tolerated. Equipment
might be used for life-support or other critical systems.
Who as the ultimate responsibility for identifying the class to which the assembly is evaluated? -
ANS The Customer.
Shall - ANS Invokes a requirement for manufacturers of all classes or product, and failure to
comply with the requirement is a noncompliance to this standard.
Order of Precedence in event of conflict 1 - ANS 1. Procurement as agreed and documented
between customer and supplier.
Order of Precedence in event of conflict 2 - ANS Master drawing or master ass. drawing
reflecting the customer's detailed requirements.
2026/2027 ALLRIGHTS RESERVED
1
, Order of Precedence in event of conflict 3 - ANS IPC-1-610 when invoked by the customer or
contract.
If documents other than IPC-A-610 are cited, the order of precedence shall be defined in the _ -
ANS Procurement documents
Target Condition - ANS A condition that is close to perfect, but is not always achievable and
may not be necessary to ensure the reliability of the assembly.
Acceptable Condition - ANS A condition that, while not necessarily perfect, will maintain
integrity and reliability of the assembly
Defect Condition - ANS The form, fit or function of the assembly is inadequate for use in its
end use environment.
A defect for Class 1... - ANS automatically implies a defect for Class 2 and 3. A defect for Class
2 implies a defect for Class 3.
Disposition - ANS The determination of how defects should be treated. These include rework,
use as is, scrap, and repair.
Who dispositions defect conditions? - ANS The manufacturer, based on design, service and
customer requirements.
Process Indicator Conditions - ANS A condition (not a defect) that does not affect the form, fit
or function of a product.
Process indicators should be... - ANS monitored as part of the process control system
Is disposition of individual process indicators required? - ANS No, and affected products
should be used as-is.
2026/2027 ALLRIGHTS RESERVED
2
