CDC 2W051 SET B | 251 QUESTIONS AND ANSWERS |
WINTER 2026 | WITH COMPLETE SOLUTION.
Before using an electrical drill, what is the first thing you should do? Answer -
Make sure the diameter of the hole to be drilled is within the capacity of the
drill.
The purpose of cutting lubricant in most drilling operations is to increase the
Answer - drilling speed and the drill bit life
which minimum articles of safety gear must be worn when using a bench
grinder Answer - Eye and Face protection
An Electrical saw blade must be operating at what speed before it contacts the
material being cut? Answer - Full
How many pounds per square inch (psi) of clean, dry air is required at the tool
end of the air hose to ensure the tool is operating safely and efficiently?
Answer - 90
What condition would prevent an operator rom applying power to a hoist or
other powered lifting device? Answer - An AF Form 979 is attached to the unit.
What should be worn anytime there is a potential for injury from overhead
objects during a lifting operation. Answer - Protective helmets
,What is the most common type of lifting sling used in the munitions career
field? Answer - Wire rope
The following are all good safety practices to follow when using a lifting sling
except Answer - inspecting the sling by passing your bare hand over the body
of the sling
The annunciators displayed on the Fluke 8025 series millimeter are used to
distinguish among. Answer - Ohms, Kilohms, and megohms
What are the two operational modes of the Fluke 8025-series multimeter?
Answer - Range and hold
The sterring system on the MHU-141/M trailer has a turning radius of how
many inches? Answer - 200
When the MHU-141 trailer is loaded or towed with the hinged deck open, what
must be done? Answer - The deck-panel supports must be properly positioned
and locked in place with quick-release pins.
What is the maximum load capacity of the MHU-110/M trailer? Answer -
15,000 pounds
The parking brake on the MHU-110/M is applied by Answer - pulling either
one of two hand levers located on each side of the front of trailer.
How many openings (hinged door panels) are on the deck of the MHU-226
trailer? Answer - three
, What type of steering aids the MHU-226 in a tighter steering radius? Answer -
Four-wheel double Ackerman
What kind of movement supports on-base activities to or from the flightline?
Answer - Operational
After 463L pallets are positioned trailer, what can you use to secure the pallets
to the trailer? Answer - MB-1 chain assemblies and/or tie-down straps
What munitions item is not loaded into transport modules by munitions
personnel? Answer - 20mm
What transport module used for decoy munitions has a maximum capacity of
30 magazines? Answer - ALE-50
How often should the positive locking device on the doors of munitions
transport modules be checked? Answer - After loading, unloading, and
periodically between stops
The purpose of the transport beam beneath the lift arm assemblies on the MJ-
1 series lift truck is to Answer - provide added support and to relieve hydraulic
pressure from the lift arms when carrying loads for long distances
What is the lifting capacity of the MJ-1 series lift truck? Answer - 3,000 pounds
What is the lifting capacity of the MHU-83-series lift truck? Answer - 7,000
pounds
when using the MHU-83 series lift with fork adapters, you immediately Answer
- reduce the lifting capability by 1000 pounds
WINTER 2026 | WITH COMPLETE SOLUTION.
Before using an electrical drill, what is the first thing you should do? Answer -
Make sure the diameter of the hole to be drilled is within the capacity of the
drill.
The purpose of cutting lubricant in most drilling operations is to increase the
Answer - drilling speed and the drill bit life
which minimum articles of safety gear must be worn when using a bench
grinder Answer - Eye and Face protection
An Electrical saw blade must be operating at what speed before it contacts the
material being cut? Answer - Full
How many pounds per square inch (psi) of clean, dry air is required at the tool
end of the air hose to ensure the tool is operating safely and efficiently?
Answer - 90
What condition would prevent an operator rom applying power to a hoist or
other powered lifting device? Answer - An AF Form 979 is attached to the unit.
What should be worn anytime there is a potential for injury from overhead
objects during a lifting operation. Answer - Protective helmets
,What is the most common type of lifting sling used in the munitions career
field? Answer - Wire rope
The following are all good safety practices to follow when using a lifting sling
except Answer - inspecting the sling by passing your bare hand over the body
of the sling
The annunciators displayed on the Fluke 8025 series millimeter are used to
distinguish among. Answer - Ohms, Kilohms, and megohms
What are the two operational modes of the Fluke 8025-series multimeter?
Answer - Range and hold
The sterring system on the MHU-141/M trailer has a turning radius of how
many inches? Answer - 200
When the MHU-141 trailer is loaded or towed with the hinged deck open, what
must be done? Answer - The deck-panel supports must be properly positioned
and locked in place with quick-release pins.
What is the maximum load capacity of the MHU-110/M trailer? Answer -
15,000 pounds
The parking brake on the MHU-110/M is applied by Answer - pulling either
one of two hand levers located on each side of the front of trailer.
How many openings (hinged door panels) are on the deck of the MHU-226
trailer? Answer - three
, What type of steering aids the MHU-226 in a tighter steering radius? Answer -
Four-wheel double Ackerman
What kind of movement supports on-base activities to or from the flightline?
Answer - Operational
After 463L pallets are positioned trailer, what can you use to secure the pallets
to the trailer? Answer - MB-1 chain assemblies and/or tie-down straps
What munitions item is not loaded into transport modules by munitions
personnel? Answer - 20mm
What transport module used for decoy munitions has a maximum capacity of
30 magazines? Answer - ALE-50
How often should the positive locking device on the doors of munitions
transport modules be checked? Answer - After loading, unloading, and
periodically between stops
The purpose of the transport beam beneath the lift arm assemblies on the MJ-
1 series lift truck is to Answer - provide added support and to relieve hydraulic
pressure from the lift arms when carrying loads for long distances
What is the lifting capacity of the MJ-1 series lift truck? Answer - 3,000 pounds
What is the lifting capacity of the MHU-83-series lift truck? Answer - 7,000
pounds
when using the MHU-83 series lift with fork adapters, you immediately Answer
- reduce the lifting capability by 1000 pounds
