CSEN 102 Introduction to Computer Science 80+ M2 SA0s

SA1 Configure a static route from R3 to redirect all traffic to R1. Use next-hop ip address. Use the router prompt below. ipv6 route ::/0 2001:DB8:CAFE:A003::1 Refer to the diagram below. What commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.254? 3 and 5 sagot ko - j Configure a static route from R3 to redirect all traffic to R2 with administrative distance 2. Use the next-hop ip address. Use the router prompt below. ipv6 route ::/0 2001:DB8:CAFE:A002::1 2 Ipv4 : S* ⇐= ipv6 : _______ Refer to the diagram. You are currently working on router 2 with the prompt below. If you want to determine the ip address assigned to its interfaces and want to know the status of the interface and protocols assigned to it, what command are you going to use? Question 7 A network administrator is currently working on a cisco router and has no idea of the topological map of the network. If he wants to see the directly connected cisco devices, what command will he execute? Use the prompt below: Router# Question 8 A network administrator is experiencing external web pages taking longer than normal to load.The web page does eventually load on the machine. Which troubleshooting commands can be used with to locate where the issue is in the network? Question 9 A network administrator is currently troubleshooting a cisco router. If he wants to verify the operational status and IP address of an interface, what command will be used? Use the prompt below: Router(config)# Do show ip interface brief Where should the default static route be configured in the given topology? R1 If you are to execute tracert 192.168.2.5 from pc1, what will be the first ip address listed on the tracert table? 172.16.3.1 Where should the default static route be configured in the topology? HQ Question 13 What do you call a network that runs both IPv4 and IPv6 routing protocols? Dual-stack Configure a summary static route on isp router to reach the company network. Use the router prompt below. ip route 192.168.40.0 255.255.255.0 209.165.202.158 Question 15 Analogy: _____ : Open == CDP : Cisco LLDP Question 16 A network administrator is currently working on a cisco router and has no idea of the topological map of the network. If he wants to see all the directly connected devices regardless of the vendor, what command will he execute? Use the prompt below: Router# Show LLDP neighbors Question 17 When wireless client is not connecting, which of the following can be checked? Verify that the PC has received an IP address via DHCP or is configured with a static IP address. Connect the device to the wired LAN and ping a known IP address. If necessary, reload drivers as appropriate for the client. Check the channel settings on the wireless client. Refer to the diagram. If standard static route is configured on r2. How many s can be seen on the routing table? 3 Refer to the diagram. If you run the command below, assuming that the ip address is active on the network, how many hops (number only) can be seen on the output considering the s0/1/1 on r1 is administratively down? 4 W hat are the different ways network router can learn its routes? Refer to the diagram. You want to test the floating static route is working between r1 and r2 lan host using the 10th usable ipv6. Using the router prompt below. How will you do it? Do show ipv6 route static | begin :: Hey: ping 2001:db8:acad:2::/64 Refer to the diagram. You are currently working on router 3 with the prompt below and want to verify only ipv6 static routes in the routing table. What command will you typed-in? do show ipv6 route Create a standard static route entry on r3 to a lan on r1 using the next-hop ip address. Use the router prompt below. Ip route 172.16.3.0 255.255.255.0 192.168.1.2 Question 24 Analogy: OSPFv2 : Link State == BGP-4 : _________ Path Vector tracert 172.16.3.2 Create a default static route on r3 to r2 using the next-hop ip address. Use the router prompt below. Ip route 0.0.0.0 0.0.0.0 192.168.1.2 Refer to the diagram. Configure a fully specified static route from r3 going to the r2 lan. Use the router prompt below. Ip route 172.16.1.0 255.255.255.0 s0/1/1 192.168.1.2 Choice 1 and 2 Refer to Figure. Your objective is provide connectivity between the 192.168.1.0/24 and 10.0.0.0/8 networks. Which command(s) will accomplish your task? Unselect local router exit interface ip address ← What are the options that you can use to configure static ip routing? As you troubleshoot configuration, you noticed that the there is an incorrect configuration on r2. Your tasked to remove the incorrect configuration. Use the router prompt below: no ip route 172.16.3.0 255.255.255.0 192.168.1.1 You are currently working on r1 and want to ping the r2 lan interface from r1 lan interface. Use the router prompt below. Do ping ipv6 2001:DB8:CAFE:A001::2 You are currently working on r1 and want to ping the r2 lan interface. Use the router prompt below. hey: do ping ipv6 2001:DB8:CAFE:2::1 Which of the following applies to wireless Lan controller configuration procedures?