1|Page
MICHIGAN STATE BRAKES CERTIFICATION EXAM LATEST 2026-2027
ACTUAL EXAM WITH COMPLETE QUESTIONS AND CORRECT
DETAILED ANSWERS (100% VERIFIED ANSWERS) |ALREADY
GRADED A+| ||PROFESSOR VERIFIED|| ||BRANDNEW!!!||
Tech A lubricates the pivot points and cables of the parking brake
system whenever it is serviced. Tech B pulls the parking brake
lever to its stop, then adjusts the cable so that the rear wheels are
locked. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-A
Tech A says the dust boot of a brake caliper should be removed
and a large dull screwdriver used to pry the piston out of its bore.
Tech B says air pressure should injected into the bleeder screw's
bore to force the piston out of the brake caliper. Who is right?
A. A only
B. B only
,2|Page
C. A and B
D. Neither - ANSWER-B
The brake warning light on the dash stays on all the time, which of
the following could be the cause of the problem?
A. misadjusted brake light switch
B. The fuse is blown in that circuit
C. A problem in the hydraulic circuit
D. The brake light switch is shorted - ANSWER-A
Which of the following would be the LEAST likely cause for an
intermittent problem in an ABS system?
A. Damaged electrical connectors at the wheel sensors
B. Damaged electrical terminals at the solenoids
C. Loose electrical connections at the control unit
D. Open wheel sensor circuit - ANSWER-D
,3|Page
The front brakes of a car equipped with disc brakes in the front
and drum brakes in the rear, grab quickly as light pressure is
applied to the brake pedal, which of the following could be the
cause of the problem?
A. Defective metering valve
B. Worn rear brakes
C. Defective proportioning valve
D. Low fluid level - ANSWER-A
Tech A says when you are installing a new set of brake shoes a
small amount of brake grease should be put on the heel and toe
of the shoes. Tech B says when you are installing a new set of
brake shoes, grease should be put on all areas of the backing
plate where there is metal to metal contact. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
, 4|Page
While discussing the probable causes for a slow returning brake
pedal: Tech A says a leaking hydraulic line could cause the
problem. Tech B says a clogged quick tape-up valve could cause
the problem. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Which of the following is not correct in the procedure for replacing
brake pads in a disc brake system?
A. Remove brake fluid from the master cylinder before loosening
the caliper to remove the pads
B. Use a c-clamp to push the piston back into its bore before
removing the brake pads
C. Remove the piston from the caliper and clean all rust,
corrosion, and dirt
MICHIGAN STATE BRAKES CERTIFICATION EXAM LATEST 2026-2027
ACTUAL EXAM WITH COMPLETE QUESTIONS AND CORRECT
DETAILED ANSWERS (100% VERIFIED ANSWERS) |ALREADY
GRADED A+| ||PROFESSOR VERIFIED|| ||BRANDNEW!!!||
Tech A lubricates the pivot points and cables of the parking brake
system whenever it is serviced. Tech B pulls the parking brake
lever to its stop, then adjusts the cable so that the rear wheels are
locked. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-A
Tech A says the dust boot of a brake caliper should be removed
and a large dull screwdriver used to pry the piston out of its bore.
Tech B says air pressure should injected into the bleeder screw's
bore to force the piston out of the brake caliper. Who is right?
A. A only
B. B only
,2|Page
C. A and B
D. Neither - ANSWER-B
The brake warning light on the dash stays on all the time, which of
the following could be the cause of the problem?
A. misadjusted brake light switch
B. The fuse is blown in that circuit
C. A problem in the hydraulic circuit
D. The brake light switch is shorted - ANSWER-A
Which of the following would be the LEAST likely cause for an
intermittent problem in an ABS system?
A. Damaged electrical connectors at the wheel sensors
B. Damaged electrical terminals at the solenoids
C. Loose electrical connections at the control unit
D. Open wheel sensor circuit - ANSWER-D
,3|Page
The front brakes of a car equipped with disc brakes in the front
and drum brakes in the rear, grab quickly as light pressure is
applied to the brake pedal, which of the following could be the
cause of the problem?
A. Defective metering valve
B. Worn rear brakes
C. Defective proportioning valve
D. Low fluid level - ANSWER-A
Tech A says when you are installing a new set of brake shoes a
small amount of brake grease should be put on the heel and toe
of the shoes. Tech B says when you are installing a new set of
brake shoes, grease should be put on all areas of the backing
plate where there is metal to metal contact. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
, 4|Page
While discussing the probable causes for a slow returning brake
pedal: Tech A says a leaking hydraulic line could cause the
problem. Tech B says a clogged quick tape-up valve could cause
the problem. Who is right?
A. A only
B. B only
C. A and B
D. Neither - ANSWER-B
Which of the following is not correct in the procedure for replacing
brake pads in a disc brake system?
A. Remove brake fluid from the master cylinder before loosening
the caliper to remove the pads
B. Use a c-clamp to push the piston back into its bore before
removing the brake pads
C. Remove the piston from the caliper and clean all rust,
corrosion, and dirt
