NEW MEXICO EE-98 ELECTRICAL CONTRACTOR
EXAM NEWEST 2026 UPDATE REAL PRACTICE
EXAM QUESTIONS & CORRECT ANSWERS |
ALREADY GRADED A+
Content covered (most tested areas): National Electrical
Code (NEC) application, service calculations, grounding
and bonding, motors, transformers, overcurrent
protection, wiring methods, conductor sizing, special
occupancies, load calculations, safety requirements,
electrical theory, and New Mexico amendments.
1. A continuous load is defined as a load where the maximum
current is expected to continue for at least how long?
A. 1 hour
B. 2 hours
C. 3 hours
D. 4 hours
Continuous loads are defined by the NEC as those expected to run
at maximum current for 3 hours or more.
2. What is the minimum size copper grounding electrode conductor
for a 200-amp service using a rod electrode?
A. 8 AWG
B. 6 AWG
C. 4 AWG
D. 2 AWG
, NEC Table 250.66 permits 6 AWG copper for rod, pipe, or plate
electrodes regardless of service size.
3. The standard utilization voltage for most residential receptacles is:
A. 208 volts
B. 240 volts
C. 120 volts
D. 277 volts
Typical dwelling receptacles supply 120 volts from a 120/240 V
single-phase system.
4. GFCI protection is required for receptacles installed in which
location?
A. Bedrooms
B. Living rooms
C. Dining rooms
D. Bathrooms
Bathrooms are among the mandatory GFCI locations per NEC
210.8.
5. What is the minimum working clearance in front of 480-volt
equipment (condition 2)?
A. 2 feet
B. 2.5 feet
C. 3 feet
D. 4 feet
NEC 110.26 requires 3 ft minimum for 151–600 V to ground under
condition 2.
6. A 20-amp branch circuit using copper conductors must use a
minimum conductor size of:
, A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
12 AWG copper is rated for 20 amps under typical conditions.
7. Overcurrent protection protects against:
A. Voltage drop
B. Ground faults only
C. Mechanical damage
D. Overload and short circuit
OCPDs are designed to interrupt excessive current conditions.
8. The grounded conductor is commonly called the:
A. Hot
B. Equipment ground
C. Bonding jumper
D. Neutral
The grounded conductor carries return current under normal
operation.
9. EMT conduit is permitted in:
A. Hazardous locations Class I Div 1
B. Underground direct burial
C. Dry or damp locations
D. Corrosive environments without protection
EMT is suitable for dry and damp areas but not severe corrosion or
burial.
10. The purpose of bonding is to:
A. Increase voltage
EXAM NEWEST 2026 UPDATE REAL PRACTICE
EXAM QUESTIONS & CORRECT ANSWERS |
ALREADY GRADED A+
Content covered (most tested areas): National Electrical
Code (NEC) application, service calculations, grounding
and bonding, motors, transformers, overcurrent
protection, wiring methods, conductor sizing, special
occupancies, load calculations, safety requirements,
electrical theory, and New Mexico amendments.
1. A continuous load is defined as a load where the maximum
current is expected to continue for at least how long?
A. 1 hour
B. 2 hours
C. 3 hours
D. 4 hours
Continuous loads are defined by the NEC as those expected to run
at maximum current for 3 hours or more.
2. What is the minimum size copper grounding electrode conductor
for a 200-amp service using a rod electrode?
A. 8 AWG
B. 6 AWG
C. 4 AWG
D. 2 AWG
, NEC Table 250.66 permits 6 AWG copper for rod, pipe, or plate
electrodes regardless of service size.
3. The standard utilization voltage for most residential receptacles is:
A. 208 volts
B. 240 volts
C. 120 volts
D. 277 volts
Typical dwelling receptacles supply 120 volts from a 120/240 V
single-phase system.
4. GFCI protection is required for receptacles installed in which
location?
A. Bedrooms
B. Living rooms
C. Dining rooms
D. Bathrooms
Bathrooms are among the mandatory GFCI locations per NEC
210.8.
5. What is the minimum working clearance in front of 480-volt
equipment (condition 2)?
A. 2 feet
B. 2.5 feet
C. 3 feet
D. 4 feet
NEC 110.26 requires 3 ft minimum for 151–600 V to ground under
condition 2.
6. A 20-amp branch circuit using copper conductors must use a
minimum conductor size of:
, A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
12 AWG copper is rated for 20 amps under typical conditions.
7. Overcurrent protection protects against:
A. Voltage drop
B. Ground faults only
C. Mechanical damage
D. Overload and short circuit
OCPDs are designed to interrupt excessive current conditions.
8. The grounded conductor is commonly called the:
A. Hot
B. Equipment ground
C. Bonding jumper
D. Neutral
The grounded conductor carries return current under normal
operation.
9. EMT conduit is permitted in:
A. Hazardous locations Class I Div 1
B. Underground direct burial
C. Dry or damp locations
D. Corrosive environments without protection
EMT is suitable for dry and damp areas but not severe corrosion or
burial.
10. The purpose of bonding is to:
A. Increase voltage
