Please write clearly in block capitals.
Centre number
Surname _________________________________________________________________________
Forename(s) _________________________________________________________________________
Candidate signature _________________________________________________________________________
For Examiner’s Use
I declare this is my own work. Question Mark
A-
1
Candid 2
ate
level number 3–4
DESIGN AND TECHNOLOGY: 5
PRODUCT DESIGN ACTUAL 2025
6
7
PAPER MERGED WITH MARK 8
SCHEME 9
Paper 1 Technical Principles 10
11–12
Monday 2 June 2025 Morning Time allowed: 2 hours 30 minutes
13
Materials
For this paper you must have:
14
l normal writing and drawing instruments l a scientific calculator.
15
Instructions l Use black ink or black ball-point pen. Use pencil only for
drawing. l Fill in the boxes at the top of this page. l Answer all questions. l You 16
must answer the questions in the spaces provided. Do not write outside the box
around each page or on blank pages. l If you need extra space for your 17–18
answer(s), use the lined pages at the end of this book. Write the question
number against your answer(s). l Do all rough work in this book. Cross through
19
any work you do not want to be marked.
20–21
Information l The marks for questions are shown in brackets. l The maximum
mark for this paper is 120. 22–23
24
TOTAL
, 2
Do not write
outside the
box
(JUN257552101) G/KL/Jun25/G4006/V6 7552/1
Answer all questions in the spaces provided.
0 1 . 1 Identify the specific material classification of nylon.
___________________________________________________________________________________
___________________________________________________________________________________
____
0 1 2
. State two specific properties of nylon. 3
[2 marks]
Property 1 ________________________________________________________________________
Property 2 ________________________________________________________________________
(02)
G/Jun25/7552/1
, 3
Do not write
outside the
box
0 2 Use the information in Figure 1 to calculate the length of the cutter path shown.
Figure 1
Cutter path
R40
°120
Not drawn to scale.
All dimensions in mm
Show your working out.
[3 marks ]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
Length of cutter path ___________________________________ mm
Turn over for the next question
Turn over U
G/Jun25/7552/1
, 4
Do not write
outside the
box
(03)
G/Jun25/7552/1
Centre number
Surname _________________________________________________________________________
Forename(s) _________________________________________________________________________
Candidate signature _________________________________________________________________________
For Examiner’s Use
I declare this is my own work. Question Mark
A-
1
Candid 2
ate
level number 3–4
DESIGN AND TECHNOLOGY: 5
PRODUCT DESIGN ACTUAL 2025
6
7
PAPER MERGED WITH MARK 8
SCHEME 9
Paper 1 Technical Principles 10
11–12
Monday 2 June 2025 Morning Time allowed: 2 hours 30 minutes
13
Materials
For this paper you must have:
14
l normal writing and drawing instruments l a scientific calculator.
15
Instructions l Use black ink or black ball-point pen. Use pencil only for
drawing. l Fill in the boxes at the top of this page. l Answer all questions. l You 16
must answer the questions in the spaces provided. Do not write outside the box
around each page or on blank pages. l If you need extra space for your 17–18
answer(s), use the lined pages at the end of this book. Write the question
number against your answer(s). l Do all rough work in this book. Cross through
19
any work you do not want to be marked.
20–21
Information l The marks for questions are shown in brackets. l The maximum
mark for this paper is 120. 22–23
24
TOTAL
, 2
Do not write
outside the
box
(JUN257552101) G/KL/Jun25/G4006/V6 7552/1
Answer all questions in the spaces provided.
0 1 . 1 Identify the specific material classification of nylon.
___________________________________________________________________________________
___________________________________________________________________________________
____
0 1 2
. State two specific properties of nylon. 3
[2 marks]
Property 1 ________________________________________________________________________
Property 2 ________________________________________________________________________
(02)
G/Jun25/7552/1
, 3
Do not write
outside the
box
0 2 Use the information in Figure 1 to calculate the length of the cutter path shown.
Figure 1
Cutter path
R40
°120
Not drawn to scale.
All dimensions in mm
Show your working out.
[3 marks ]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
Length of cutter path ___________________________________ mm
Turn over for the next question
Turn over U
G/Jun25/7552/1
, 4
Do not write
outside the
box
(03)
G/Jun25/7552/1
