NEVADA A GENERAL ENGINEERING PRACTICE
EXAM 2026 FINAL EXAM PAPER COMPLETE
QUESTIONS AND SOLUTIONS
◉ The ASME code sections which are most pertinent to Fifth and
Fourth class power engineer are sections: Answer: IV and VI
◉ what code contains guidelines for the care and operation of
heating boilers? Answer: ASME Section VI
◉ When a feedwater pump feeds two of more boilers from a
common source, there must be a regulating valve Answer: Each
feedwater line to each boiler
◉ what determines the classification of the certificate of
completency required for the role of chief power engineer? Answer:
Kilowatt rating of the powerplant
◉ The provincial regulations require that all welding repairs on
boilers must be: Answer: approved by an authorized inspector
◉ A boiler in which steam is made at a present not greater than 103
Kilopascals, is properly termed a: Answer: heating plant
,◉ In the power engineers regulations definitions, ______ means any
part of the surface of a boiler that is in contact with fluid under
pressure on one side and the products of combustion on the other
side: Answer: Heating surface
◉ Heating plant means one or more boilers in which water that can
be heated pressure and temperature of not more than: Answer:
1,100 kPa and a temp of 121c
◉ The letters CRN stands for Answer: Canadian registration number
◉ Heat passes through the metal of heating surfaces by: Answer:
conduction
◉ Six kg would be a measure of an object's: Answer: mass
◉ the term used to describe the fluid to gas change of state during
the addition of heat is latent heat of: Answer: evapotarion
◉ the fahrenheit scale considers the boiling point of water to be
Answer: 212c
, ◉ The three meathods of heat transfer are: Answer: Radiation,
conduction and convection
◉ Water extinguishes a fire by: Answer: cooling the combustible
material
◉ Water hammer can be prevented or minimized by installing___
chambers on a piping system. Answer: "end of line" air
◉ when working below ground level, the work presents the danger
of : Answer: falling objects
◉ Under WHMIS legislation all workers have the right to Answer:
Know what material they are working with
◉ of the following materials, which would be classified as a class B
fire? Answer: Paper
◉ The correct safe working angle for a ladder is: Answer: 1 to 4
◉ overhead work presents the danger of ____ to others in the area.
Answer: falling objects
◉ The damaging factor of an electrical circuit is the: Answer: current
EXAM 2026 FINAL EXAM PAPER COMPLETE
QUESTIONS AND SOLUTIONS
◉ The ASME code sections which are most pertinent to Fifth and
Fourth class power engineer are sections: Answer: IV and VI
◉ what code contains guidelines for the care and operation of
heating boilers? Answer: ASME Section VI
◉ When a feedwater pump feeds two of more boilers from a
common source, there must be a regulating valve Answer: Each
feedwater line to each boiler
◉ what determines the classification of the certificate of
completency required for the role of chief power engineer? Answer:
Kilowatt rating of the powerplant
◉ The provincial regulations require that all welding repairs on
boilers must be: Answer: approved by an authorized inspector
◉ A boiler in which steam is made at a present not greater than 103
Kilopascals, is properly termed a: Answer: heating plant
,◉ In the power engineers regulations definitions, ______ means any
part of the surface of a boiler that is in contact with fluid under
pressure on one side and the products of combustion on the other
side: Answer: Heating surface
◉ Heating plant means one or more boilers in which water that can
be heated pressure and temperature of not more than: Answer:
1,100 kPa and a temp of 121c
◉ The letters CRN stands for Answer: Canadian registration number
◉ Heat passes through the metal of heating surfaces by: Answer:
conduction
◉ Six kg would be a measure of an object's: Answer: mass
◉ the term used to describe the fluid to gas change of state during
the addition of heat is latent heat of: Answer: evapotarion
◉ the fahrenheit scale considers the boiling point of water to be
Answer: 212c
, ◉ The three meathods of heat transfer are: Answer: Radiation,
conduction and convection
◉ Water extinguishes a fire by: Answer: cooling the combustible
material
◉ Water hammer can be prevented or minimized by installing___
chambers on a piping system. Answer: "end of line" air
◉ when working below ground level, the work presents the danger
of : Answer: falling objects
◉ Under WHMIS legislation all workers have the right to Answer:
Know what material they are working with
◉ of the following materials, which would be classified as a class B
fire? Answer: Paper
◉ The correct safe working angle for a ladder is: Answer: 1 to 4
◉ overhead work presents the danger of ____ to others in the area.
Answer: falling objects
◉ The damaging factor of an electrical circuit is the: Answer: current
