1|Page
Nccer boilermaker Final Verified Exam Newest Exam
Preparation Newest With Complete Questions And
Correct Detailed Answers|| Newest Exam!!!
What is the piece of equipment inside a tower that
maintains the heights of the liquid? - Answer-Weir
Torque is normally measured in: - Answer-Foot Pounds
An operator raises that boom. What happens to the
location of the load? - Answer-It moves towards the crane
and goes up.
What type of glove should be used with oxyfuel cutting? -
Answer-Gauntlet welding gloves
What are drift pins designed for? - Answer-Align bolt holes
in a flan
A threaded elbow that has a male thread on one side is
referred to as a (n): - Answer-Street Elbow
,2|Page
In case where there is no fill ports for hydro test on an
exchanger, what can be used? - Answer-Bleeder Blind
All of the following are true of pneumatic testing, EXCEPT:
- Answer-Demineralized water must be used.
What type of boll can be used as a lifting device? -
Answer-Eye
The two steps in making up threaded joints are the hand
engagement and: - Answer-Wrench Makeup
where should liquid Teflon lubricants be applied to pipe
threads? - Answer-On both male and female threads.
What type of valve requires a 90 degree turn of the handle
to fully open or close it? - Answer-Ball Valve
While pressuring up an exchanger with a pneumatic test
pump, what should be watched closely? - Answer-The test
gauge for over pressuring.
, 3|Page
What is the weight of a solid cylinder with a diameter of 6'
and a length of 10' that was made of a
steel that weighs 490 pounds per cubic foot? (round)? -
Answer-138.544 lbs.
The purpose of a tie rod is to: - Answer-Anchor baffles in
place
What is NOT a cleaning medium for a piping system? -
Answer-Pigs
What is the typical method for locking newly installed
tubes in a tube sheet? - Answer-Rolling
According to OSHA, the fall protection tie off point MUST
have a MINIMUM rating of: - Answer-5,000 lbs
Before metal can be cut using oxyfuel, one important step
is to properly lay out the cup by marking
it with. - Answer-Soapstone or punch marks.
Nccer boilermaker Final Verified Exam Newest Exam
Preparation Newest With Complete Questions And
Correct Detailed Answers|| Newest Exam!!!
What is the piece of equipment inside a tower that
maintains the heights of the liquid? - Answer-Weir
Torque is normally measured in: - Answer-Foot Pounds
An operator raises that boom. What happens to the
location of the load? - Answer-It moves towards the crane
and goes up.
What type of glove should be used with oxyfuel cutting? -
Answer-Gauntlet welding gloves
What are drift pins designed for? - Answer-Align bolt holes
in a flan
A threaded elbow that has a male thread on one side is
referred to as a (n): - Answer-Street Elbow
,2|Page
In case where there is no fill ports for hydro test on an
exchanger, what can be used? - Answer-Bleeder Blind
All of the following are true of pneumatic testing, EXCEPT:
- Answer-Demineralized water must be used.
What type of boll can be used as a lifting device? -
Answer-Eye
The two steps in making up threaded joints are the hand
engagement and: - Answer-Wrench Makeup
where should liquid Teflon lubricants be applied to pipe
threads? - Answer-On both male and female threads.
What type of valve requires a 90 degree turn of the handle
to fully open or close it? - Answer-Ball Valve
While pressuring up an exchanger with a pneumatic test
pump, what should be watched closely? - Answer-The test
gauge for over pressuring.
, 3|Page
What is the weight of a solid cylinder with a diameter of 6'
and a length of 10' that was made of a
steel that weighs 490 pounds per cubic foot? (round)? -
Answer-138.544 lbs.
The purpose of a tie rod is to: - Answer-Anchor baffles in
place
What is NOT a cleaning medium for a piping system? -
Answer-Pigs
What is the typical method for locking newly installed
tubes in a tube sheet? - Answer-Rolling
According to OSHA, the fall protection tie off point MUST
have a MINIMUM rating of: - Answer-5,000 lbs
Before metal can be cut using oxyfuel, one important step
is to properly lay out the cup by marking
it with. - Answer-Soapstone or punch marks.
