AMPP CIP Level 2 Standards Study Questions with Correct Answers

AMPP CIP Level 2 Standards Study Questions with Correct Answers 1. Which standard defines the minimum level of surface cleanliness for thermal spray coatings in atmospheric exposure? - ANSWER NACE 2/SSPC-SP 10 or ISO SA 2 1/2 2. ASTM D 2240 - ANSWER Standard Test Method for Rubber Property- Durometer Hardness 3. ASTM 3363 - ANSWER Pencil hardness test 4. ASTM D 2583 - ANSWER standard test method for indentation hardness of rigid plastics by means of a Barcol Impressor 5. ASTM D 4138 (method A) - ANSWER Standard for a tooke Gauge 6. ASTM D 4138 method C - ANSWER Saberg Drill 7. ASTM D 3359 method B - ANSWER Cross hatch cutter (Adhesion Standard) 8. NACE SP0188 - ANSWER Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates 9. ASTM D 4752 - ANSWER test method for measuring MEK resistance of Ethyl Silicate Zinc-Rich primers by solvent rub 10. ASTM D 4541 - ANSWER STANDARD TEST METHOD FOR PULL OFF STRENGTH OF COATINGS. USING PORTABLE ADHESION TESTERS. 11. ASTM E 337 - ANSWER Standard for HYDOMETER 12. ASTM D 6132 - ANSWER Standard Test Method for Nondestructive Measurement fo Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gauge 13. ASTM Standard G 8 - ANSWER standard test method for cathodic disbanding of pipeline coating 14. Low-Pressure Water Cleaning (LP WC) - ANSWER - Below 5,000 psig - Also called "power washing" or "pressure washing" 15. High-Pressure Water Cleaning (HP WC) - ANSWER - 5,000 to 10,000 psig 16. High-Pressure Waterjetting (HP WJ) - ANSWER - 10,000 to 30,000 psig 17. Ultrahigh-Pressure Waterjetting (UHP WJ) - ANSWER - 30,000 psig and above 18. Light (L) flash rusted surface: - ANSWER Not easily removed by lightly wiping with a cloth 19. Moderate (M) flash rusted surface: - ANSWER Leaves light marks on a cloth that is lightly wiped over the surface 20. Heavy (H) flash rusted surface: - ANSWER Leaves significant marks on a cloth that is lightly wiped over the surface 21. Operators and others in the area of thermal spraying should wear No. __ green welding goggles. - ANSWER No. 6 22. SP0288 - ANSWER Inspection of linings on steel and concrete 23. SP0178 - ANSWER Design, fabrication, and surface finish practices for tanks and vessels to be lined for immersion service. 24. U.L. 1709 - ANSWER Rapid Rise Fire Tests of Protection Materials for Structural Steel 25. Surface preparation for rubber should be cleaned to a __________. - ANSWER NACE No. 1/SSPC-SP 5 with a surface profile of 1.5 to 2.5 mils 26. ASTM D 4258 - ANSWER Standard practice for surface cleaning concrete for coating 27. ASTM D 4259 - ANSWER Standard practice for abrading concrete 28. ASTM D 4260 - ANSWER Standard practice for acid etching 29. ASTM D 4263 - ANSWER Standard test method for indicating moisture in concrete by the plastic sheet method 30. NACE No. 6 / SSPC-SP 13 - ANSWER Joint surface preparation standard for surface preparation of concrete 31. For the general application of tape on a pipeline, what NACE / SSPC standard is common - ANSWER • NACE No.3 / SSPC-SP6 32. NACE TM 21240 - ANSWER • Peel test Peel test of heat shrink coatings 3 tier pass/fail criteria 33. ASTM D 1730 - ANSWER Preparation of Aluminum and Aluminum Alloy Surfaces for Painting 34. ASTM D 1731 - ANSWER Preparation of Hot Dip Aluminum Surfaces for Painting 35. ASTM D 1732 - ANSWER Preparation of Magnesium Surfaces for Painting 36. SSPC-SP 16 - ANSWER Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steel, and Non-Ferrous Metals