FIREFIGHTER 1 & 2 STATE TEST EXAM WITH COMPLETE
SOLUTIONS GUARANTEED PASS (2026 LATEST)
Which rescue tool power source is typically powered by
pumps? - ANSWER ->Hydraulic
What stabilizing tool uses a system of at least three wedged
posts between the ground and a vehicle resting on its side or
top? - ANSWER ->Buttress tension system
Hybrid vehicles that use color coded wiring use to mark
high voltage wiring. - ANSWER ->Orange
When using a strut and buttress tension system, firefighters
must ensure all parts have a safety margin that is: - ANSWER -
>In excess of the weight being secured
What type of extrication method is used to stabilize a vehicle
that is upside down or lying on its side? - ANSWER ->Buttress
tension system
What initial action is the next priority after stabilizing the
scene? - ANSWER ->Stabilize the victim
What type of structural collapse occurs when the floor and/or
roof assemblies on both sides of a load-bearing wall collapse,
allowing a good chance of victim survival? - ANSWER ->A-frame
,In the OATH method of signaling on a search line, two tugs
represents - ANSWER ->Advance
Which of the following is an example of a push/pull tool? -
ANSWER ->Pike pole
Cutting edges on axes should be inspected for: - ANSWER -
>Chips, cracks, or spurs
When caring for an unprotected metal surface, use a metal file
to: - ANSWER ->Remove burrs from a cutting edge
NFPA 1931 requires that single, roof combination and extension
ladders must support a maximum load of - ANSWER ->750 lbs
Ground ladders should be service tested before being placed in
service, while in service, and after use that exposes the
ladder to high heat or rough treatment. - ANSWER ->Once each
year
Which of the following describes the best placement of a ladder
to be used for entry or rescue from a window? - ANSWER -
>Ladder tip slightly below sill, or wedged under sill lip
Which of the following is a reason that modern construction
may tend to contain fires for longer periods of time? - ANSWER
->Energy efficient designs
, What should a firefighter do before stepping off a ladder,
parapet wall, or other place of safety onto the roof of a burning
building, especially if the roof surface is obscured by smoke or
darkness? - ANSWER ->Sound the roof for structural integrity by
striking with an axe.
What type of hose is designed for drafting water from static
water supplies or connecting to a fire hydrant? - ANSWER -
>Hard suction hose
What type of fire hose damage can weaken the jacket which
can lead to ruptures under pressure? - ANSWER ->Organic
damage
Which of the following equipment is necessary for service
testing? - ANSWER ->Nozzles with shutoff valves
The test site for service testing should be: - ANSWER ->On a
slight grade
Which of the following procedures should be followed when
service testing fire hose? - ANSWER ->Stand away from the
discharge valve connection when charging hose
Which action of fire fighting foam creates a barrier between the
fuel and the fire? - ANSWER ->Separating
Foam lowers surface tension of water, allowing it to fires
in class A materials - ANSWER ->Penetrate
SOLUTIONS GUARANTEED PASS (2026 LATEST)
Which rescue tool power source is typically powered by
pumps? - ANSWER ->Hydraulic
What stabilizing tool uses a system of at least three wedged
posts between the ground and a vehicle resting on its side or
top? - ANSWER ->Buttress tension system
Hybrid vehicles that use color coded wiring use to mark
high voltage wiring. - ANSWER ->Orange
When using a strut and buttress tension system, firefighters
must ensure all parts have a safety margin that is: - ANSWER -
>In excess of the weight being secured
What type of extrication method is used to stabilize a vehicle
that is upside down or lying on its side? - ANSWER ->Buttress
tension system
What initial action is the next priority after stabilizing the
scene? - ANSWER ->Stabilize the victim
What type of structural collapse occurs when the floor and/or
roof assemblies on both sides of a load-bearing wall collapse,
allowing a good chance of victim survival? - ANSWER ->A-frame
,In the OATH method of signaling on a search line, two tugs
represents - ANSWER ->Advance
Which of the following is an example of a push/pull tool? -
ANSWER ->Pike pole
Cutting edges on axes should be inspected for: - ANSWER -
>Chips, cracks, or spurs
When caring for an unprotected metal surface, use a metal file
to: - ANSWER ->Remove burrs from a cutting edge
NFPA 1931 requires that single, roof combination and extension
ladders must support a maximum load of - ANSWER ->750 lbs
Ground ladders should be service tested before being placed in
service, while in service, and after use that exposes the
ladder to high heat or rough treatment. - ANSWER ->Once each
year
Which of the following describes the best placement of a ladder
to be used for entry or rescue from a window? - ANSWER -
>Ladder tip slightly below sill, or wedged under sill lip
Which of the following is a reason that modern construction
may tend to contain fires for longer periods of time? - ANSWER
->Energy efficient designs
, What should a firefighter do before stepping off a ladder,
parapet wall, or other place of safety onto the roof of a burning
building, especially if the roof surface is obscured by smoke or
darkness? - ANSWER ->Sound the roof for structural integrity by
striking with an axe.
What type of hose is designed for drafting water from static
water supplies or connecting to a fire hydrant? - ANSWER -
>Hard suction hose
What type of fire hose damage can weaken the jacket which
can lead to ruptures under pressure? - ANSWER ->Organic
damage
Which of the following equipment is necessary for service
testing? - ANSWER ->Nozzles with shutoff valves
The test site for service testing should be: - ANSWER ->On a
slight grade
Which of the following procedures should be followed when
service testing fire hose? - ANSWER ->Stand away from the
discharge valve connection when charging hose
Which action of fire fighting foam creates a barrier between the
fuel and the fire? - ANSWER ->Separating
Foam lowers surface tension of water, allowing it to fires
in class A materials - ANSWER ->Penetrate
