Brannigan's Chapter 11 || A+ Certified.
What material is typically limited to exterior walls and shaft enclosures in Type II construction?
correct answers Concrete
What is the most important metal used in building construction? correct answers Steel
The compressive strength of steel is equal to its ________________ correct answers Tensile
strength
Fire resistance is a function of ________ correct answers Mass
What will steel do if it cannot elongate because of a restraint? correct answers Buckle or overturn
The heat being evolved by a fire can be triaged; Name the classifications in order of priority
Hint: A, E, L correct answers - Heat being absorbed by contents or structural elements that will
be ignited or caused to fail
- Heat being evolved from contents that are burning
- Heat leaving the structure
What is the fire department's heat removal medium? correct answers Water
If steel is _____________, the water freezes it in whatever shape it is in correct answers Failing
If steel is ________________, the cooling effect of water draws it back to its original dimensions
correct answers Elongating
A steel member that has two legs at right angles to one another. They are "L" shaped in cross
section correct answers Angles
Plate that is fewer than 6 inches in width, are also made square or round correct answers Bar
A large hollow column built from steel plates correct answers Box column
A square or rectangular steel girder that is hollow, like a box column, and used to support other
beams in buildings; Large ones are used to construct bridges correct answers Box girder
A wide flange beam that has been cut in half in a zig zag pattern and then welded back together
offset, creating a new, deeper beam correct answers Castellated beam
A steel structural component that has a square, "U"shaped cross section correct answers Channel
A beam shaped like the letter "I". The top and bottom of the "I" are called flanges, and the stem
is called the web. correct answers I-beam
, Flat pieces of steel correct answers Plates
Beams, usually channels, set at right angles to trusses or of rafters to provide support for
lightweight roofing correct answers Purlins
Steel structural member that is one solid piece of metal correct answers Rolled up member
Steel structural member that is made up of different sections riveted, bolted, or welded together
correct answers Built up members
A girder built from a steel plate with angles riveted on each side of the top and bottom to form
flanges is often called what? correct answers Plate girder
A column made of vertical units connected with diagonal pieces correct answers Lattice column
A girder that ties wall columns together in a framed building; Also carries the weight of the
panel wall correct answers Spandrel girder
A standard I-beam cut lengthwise through the web forms two such beams with "T" shaped cross
sections correct answers Tee
A steel structural member that is rolled on cylindrical, square, or rectangular shape that is most
often used as a column correct answers Tube
I-beams that have flanges wider than those found in standard I-beams; Some are "H" shaped and,
because they are square, are more suitable for columns correct answers Wide flange shapes
What is often the first structure that comes to mind when steel is mentioned as a construction
material? correct answers High-rise buildings
Name the letters abbreviations that go with each different shaped steel member
- Channel
- Castellated beams
- Angles
- America Standard (I-Beam)
- Wide flange beams and columns
- Structural tees correct answers C - Channel
CB - Castellated beams
L - Angles
S - America Standard (I-Beam)
WF - Wide flange beams and columns
WT - Structural tees
What material is typically limited to exterior walls and shaft enclosures in Type II construction?
correct answers Concrete
What is the most important metal used in building construction? correct answers Steel
The compressive strength of steel is equal to its ________________ correct answers Tensile
strength
Fire resistance is a function of ________ correct answers Mass
What will steel do if it cannot elongate because of a restraint? correct answers Buckle or overturn
The heat being evolved by a fire can be triaged; Name the classifications in order of priority
Hint: A, E, L correct answers - Heat being absorbed by contents or structural elements that will
be ignited or caused to fail
- Heat being evolved from contents that are burning
- Heat leaving the structure
What is the fire department's heat removal medium? correct answers Water
If steel is _____________, the water freezes it in whatever shape it is in correct answers Failing
If steel is ________________, the cooling effect of water draws it back to its original dimensions
correct answers Elongating
A steel member that has two legs at right angles to one another. They are "L" shaped in cross
section correct answers Angles
Plate that is fewer than 6 inches in width, are also made square or round correct answers Bar
A large hollow column built from steel plates correct answers Box column
A square or rectangular steel girder that is hollow, like a box column, and used to support other
beams in buildings; Large ones are used to construct bridges correct answers Box girder
A wide flange beam that has been cut in half in a zig zag pattern and then welded back together
offset, creating a new, deeper beam correct answers Castellated beam
A steel structural component that has a square, "U"shaped cross section correct answers Channel
A beam shaped like the letter "I". The top and bottom of the "I" are called flanges, and the stem
is called the web. correct answers I-beam
, Flat pieces of steel correct answers Plates
Beams, usually channels, set at right angles to trusses or of rafters to provide support for
lightweight roofing correct answers Purlins
Steel structural member that is one solid piece of metal correct answers Rolled up member
Steel structural member that is made up of different sections riveted, bolted, or welded together
correct answers Built up members
A girder built from a steel plate with angles riveted on each side of the top and bottom to form
flanges is often called what? correct answers Plate girder
A column made of vertical units connected with diagonal pieces correct answers Lattice column
A girder that ties wall columns together in a framed building; Also carries the weight of the
panel wall correct answers Spandrel girder
A standard I-beam cut lengthwise through the web forms two such beams with "T" shaped cross
sections correct answers Tee
A steel structural member that is rolled on cylindrical, square, or rectangular shape that is most
often used as a column correct answers Tube
I-beams that have flanges wider than those found in standard I-beams; Some are "H" shaped and,
because they are square, are more suitable for columns correct answers Wide flange shapes
What is often the first structure that comes to mind when steel is mentioned as a construction
material? correct answers High-rise buildings
Name the letters abbreviations that go with each different shaped steel member
- Channel
- Castellated beams
- Angles
- America Standard (I-Beam)
- Wide flange beams and columns
- Structural tees correct answers C - Channel
CB - Castellated beams
L - Angles
S - America Standard (I-Beam)
WF - Wide flange beams and columns
WT - Structural tees