JLTV Test A (2024) Questions
and Answers 100% PASS
Fill in the blanks in the vehicle hierarchy below: - CORRECT ANSWER-UTL
GENERAL PURPOSE
HEAVY
CLOSE COMBAT
TRAILER
2. Why do the High Pressure Gas (HPG) pumps automatically stop running after running
continuously for 10 minutes?
A. To prevent overcharging of the suspension components and HPG Spring components
B. To prevent the SPNSN ERROR light from illuminating
C. To prevent the hydraulic pumps that power the springs' pumps from overheating
D. To prevent system leakage - CORRECT ANSWER-C. To prevent the hydraulic pumps that
power the springs' pumps from overheating
3. The transaxle receives power from the
A. Engine
, B. Transmission
C. CTIS
D. Suspension system - CORRECT ANSWER-Transmission
Height for mudding stuff - CORRECT ANSWER-30in, 60in
5. Air over hydraulic brakes function by:
A. The engine-driven belt provides power to the hydraulic pumps for the brakes.
B. The air pressure for service brakes is monitored by the CTIS, CTIS sends the signal to the
hydraulic components of when to apply or not apply.
C. The CAC controls the air circulation directly to the service brake, when the service brake is
engaged it pushes hydraulic fluid through the lines to activate the brakes.
When the air system is charged, the air pressure holds the hydraulic braking components
open so they cannot apply; when service brake applied, it drops psi allowing hydraulic
components to apply/engage. - CORRECT ANSWER-When the air system is charged, the air
pressure holds the hydraulic braking components open so they cannot apply; when service
brake applied, it drops psi allowing hydraulic components to apply/engage.
Locate the buttons on the MUX panel - CORRECT ANSWER-Blackout Switch
Head Lights and Clearence Lights
Internal Dome Light Selector
Dome Light Dimmer
Dash Light Dimmer
© 2026 Copyright. All Rights Reserved. This document is
protected by copyright law
and Answers 100% PASS
Fill in the blanks in the vehicle hierarchy below: - CORRECT ANSWER-UTL
GENERAL PURPOSE
HEAVY
CLOSE COMBAT
TRAILER
2. Why do the High Pressure Gas (HPG) pumps automatically stop running after running
continuously for 10 minutes?
A. To prevent overcharging of the suspension components and HPG Spring components
B. To prevent the SPNSN ERROR light from illuminating
C. To prevent the hydraulic pumps that power the springs' pumps from overheating
D. To prevent system leakage - CORRECT ANSWER-C. To prevent the hydraulic pumps that
power the springs' pumps from overheating
3. The transaxle receives power from the
A. Engine
, B. Transmission
C. CTIS
D. Suspension system - CORRECT ANSWER-Transmission
Height for mudding stuff - CORRECT ANSWER-30in, 60in
5. Air over hydraulic brakes function by:
A. The engine-driven belt provides power to the hydraulic pumps for the brakes.
B. The air pressure for service brakes is monitored by the CTIS, CTIS sends the signal to the
hydraulic components of when to apply or not apply.
C. The CAC controls the air circulation directly to the service brake, when the service brake is
engaged it pushes hydraulic fluid through the lines to activate the brakes.
When the air system is charged, the air pressure holds the hydraulic braking components
open so they cannot apply; when service brake applied, it drops psi allowing hydraulic
components to apply/engage. - CORRECT ANSWER-When the air system is charged, the air
pressure holds the hydraulic braking components open so they cannot apply; when service
brake applied, it drops psi allowing hydraulic components to apply/engage.
Locate the buttons on the MUX panel - CORRECT ANSWER-Blackout Switch
Head Lights and Clearence Lights
Internal Dome Light Selector
Dome Light Dimmer
Dash Light Dimmer
© 2026 Copyright. All Rights Reserved. This document is
protected by copyright law
