IRONWORKER NCCER EXAM QUESTIONS
AND ANSWERS |WELL ELABORATED|
WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A
REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE? - ANSWER -VERTICLE
ALIGNMENT POSITIONER
HOW IS THE SIZE OF THE CUTTING TORCH TIP DETERMINED? - ANSWER -FROM
THE BASE METAL THICKNESS AND FUEL TYPE BEING USED
JOIST ARE SUPPORTED LATERALLY BY: - ANSWER -VERTICLE CHORDS
STORED OXYFUEL CYLINDERS MUST BE SEPERATED BY A 30 MINUTE BURN
WALL OR A DISTANCE OF AT LEAST: - ANSWER -20'
A LOAD BLOCK IS: - ANSWER -A BLOCK OF STEEL USED AS COUNTERWEIGHT
HAWG WASH IS A TYPE OF: - ANSWER -LUBRICANT
A WELDING ELECTRODE MARKED AS E7018 CAN BE USED TO WELD: - ANSWER -
IN ALL POSITIONS
JOIST RESTING ON STEEL MUST HAVE A MINIMUM BEARING OF: - ANSWER -1
INCH
WHAT IS THE MINIMUM WAITING PERIOD BEFORE USING AN ACETYLENE
CYLINDER THAT HAS TIPPED OVER? - ANSWER -30 MINUTES
ONE OF THE LIMIT SWITCHES ON A CRANE IS CALLED A(N): - ANSWER -ANTI
TWO BLOCKING DEVICE
ACETYLENE GAS REGUATORS ARE ALWAYS REDLINED AT: - ANSWER -15 PSI
REMOVING A PORTION OF THE FLANGES AT THE END OF A BEAM TO ALLOW
CONNECTION OF A BEAM TO THE WEB OF A COLUMN IS CALLED - ANSWER -
COPING
THE RELATIONSHIP BETWEEN THE SHEAVE DIAMETER AND THE ROPE
DIAMETER IS DESCRIBING THE: - ANSWER -D:D RATIO
ALL OF THE FOLLOWING CONDITIONS WOULD REQUIRE THE REMOVAL OF
RIGGING FROM SERVICE EXCEPT: - ANSWER -EXCESSIVE LUBRICATION
, IN CRANE OPERATIONS, WHAT IS A JIB? - ANSWER -AN EXTENSION OF THE MAIN
BOOM
THE MINIMUM LEVEL OF PPE THAT IS REQUIRED FOR A SPECIFIC TASK IS
DETEMINED BY: - ANSWER -THE COMPANY SAFETY DEPARTMENT
WHICH OF THE FOLLOWING IS NOT A TYPE OF DECKING? - ANSWER -CELLULAR
DECK
WHICH OF THE FOLLOWING BOLT TYPES IS KNOWN AS A "SOFT" BOLT THAT IS
GENERALLY USED IN STATIC LOAD STRUCTURES? - ANSWER -A307
WHEN STACKING OR STORING JOIST, DUNNAGE OR CRIBBING SHOULD BE
PLACED UNDER THE: - ANSWER -LATERAL ENDS
WHICH OF THE FOLLOWING CRANES ARE BEST SUITED FOR PICK AND CARRY
OPERATIONS? - ANSWER -CRAWLER CRANES
A DIE USED FOR CLEANING OR REPAIRING THREADS ON A ANCHOR ROD OR
BOLT IS CALLED A: - ANSWER -THREAD CHASER
THE ACCURACY OF A PLUMB BOB THAT IS BEING USED OUTSIDE MAY BE
AFFECTED BY: - ANSWER -WIND
WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS: - ANSWER
-CENTER OF GRAVITY
WHERE DOES THE FLUX COME FROM ON A SHEAR STUD? - ANSWER -NIPPLE ON
THE BOTTOM OF THE STUD
WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN
STRUCTURAL STEEL APPLICATIONS? - ANSWER -OXY-ACETYLENE WELDING
WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE
MEASUREMENT INSTUMENT? - ANSWER -LASER LIGHT
WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE
CONSTRUCTION SHEAR STUDS? - ANSWER -GTAW
BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN -
ANSWER -PROPERLY TESTED AND STAMPED
WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE
SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT - ANSWER -
TWISTING OF THE BUNDLE
AND ANSWERS |WELL ELABORATED|
WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A
REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE? - ANSWER -VERTICLE
ALIGNMENT POSITIONER
HOW IS THE SIZE OF THE CUTTING TORCH TIP DETERMINED? - ANSWER -FROM
THE BASE METAL THICKNESS AND FUEL TYPE BEING USED
JOIST ARE SUPPORTED LATERALLY BY: - ANSWER -VERTICLE CHORDS
STORED OXYFUEL CYLINDERS MUST BE SEPERATED BY A 30 MINUTE BURN
WALL OR A DISTANCE OF AT LEAST: - ANSWER -20'
A LOAD BLOCK IS: - ANSWER -A BLOCK OF STEEL USED AS COUNTERWEIGHT
HAWG WASH IS A TYPE OF: - ANSWER -LUBRICANT
A WELDING ELECTRODE MARKED AS E7018 CAN BE USED TO WELD: - ANSWER -
IN ALL POSITIONS
JOIST RESTING ON STEEL MUST HAVE A MINIMUM BEARING OF: - ANSWER -1
INCH
WHAT IS THE MINIMUM WAITING PERIOD BEFORE USING AN ACETYLENE
CYLINDER THAT HAS TIPPED OVER? - ANSWER -30 MINUTES
ONE OF THE LIMIT SWITCHES ON A CRANE IS CALLED A(N): - ANSWER -ANTI
TWO BLOCKING DEVICE
ACETYLENE GAS REGUATORS ARE ALWAYS REDLINED AT: - ANSWER -15 PSI
REMOVING A PORTION OF THE FLANGES AT THE END OF A BEAM TO ALLOW
CONNECTION OF A BEAM TO THE WEB OF A COLUMN IS CALLED - ANSWER -
COPING
THE RELATIONSHIP BETWEEN THE SHEAVE DIAMETER AND THE ROPE
DIAMETER IS DESCRIBING THE: - ANSWER -D:D RATIO
ALL OF THE FOLLOWING CONDITIONS WOULD REQUIRE THE REMOVAL OF
RIGGING FROM SERVICE EXCEPT: - ANSWER -EXCESSIVE LUBRICATION
, IN CRANE OPERATIONS, WHAT IS A JIB? - ANSWER -AN EXTENSION OF THE MAIN
BOOM
THE MINIMUM LEVEL OF PPE THAT IS REQUIRED FOR A SPECIFIC TASK IS
DETEMINED BY: - ANSWER -THE COMPANY SAFETY DEPARTMENT
WHICH OF THE FOLLOWING IS NOT A TYPE OF DECKING? - ANSWER -CELLULAR
DECK
WHICH OF THE FOLLOWING BOLT TYPES IS KNOWN AS A "SOFT" BOLT THAT IS
GENERALLY USED IN STATIC LOAD STRUCTURES? - ANSWER -A307
WHEN STACKING OR STORING JOIST, DUNNAGE OR CRIBBING SHOULD BE
PLACED UNDER THE: - ANSWER -LATERAL ENDS
WHICH OF THE FOLLOWING CRANES ARE BEST SUITED FOR PICK AND CARRY
OPERATIONS? - ANSWER -CRAWLER CRANES
A DIE USED FOR CLEANING OR REPAIRING THREADS ON A ANCHOR ROD OR
BOLT IS CALLED A: - ANSWER -THREAD CHASER
THE ACCURACY OF A PLUMB BOB THAT IS BEING USED OUTSIDE MAY BE
AFFECTED BY: - ANSWER -WIND
WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS: - ANSWER
-CENTER OF GRAVITY
WHERE DOES THE FLUX COME FROM ON A SHEAR STUD? - ANSWER -NIPPLE ON
THE BOTTOM OF THE STUD
WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN
STRUCTURAL STEEL APPLICATIONS? - ANSWER -OXY-ACETYLENE WELDING
WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE
MEASUREMENT INSTUMENT? - ANSWER -LASER LIGHT
WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE
CONSTRUCTION SHEAR STUDS? - ANSWER -GTAW
BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN -
ANSWER -PROPERLY TESTED AND STAMPED
WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE
SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT - ANSWER -
TWISTING OF THE BUNDLE
