Georgia Elevator Mechanic Licensure
Examination Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. What is the purpose of the governor in an elevator system?
A. To control door timing
B. To regulate overspeed protection
C. To power the controller
D. To increase traction
Rationale: The governor detects and responds to overspeed conditions,
triggering safety devices.
2. What does ASME A17.1 primarily cover?
A. Fire extinguisher placement
B. Safety code for elevators and escalators
C. Plumbing standards
D. Electrical outlet spacing
Rationale: ASME A17.1 is the American safety code governing
elevators/escalators in many jurisdictions including Georgia.Georgia
Rules and Regulations
3. In a traction elevator, what component provides friction for
movement?
A. Hydraulic ram
B. Counterweight roller
C. Drive sheave
D. Brake coil
, Rationale: The drive sheave transmits motor torque via ropes to move
the car by friction.
4. What voltage is commonly reduced from 480 V to supply control
circuits?
A. 12 V
B. 120 V
C. 240 V
D. 208 V
Rationale: A 480 V step-down transformer often produces 240 V for
control and logic circuits.
5. What must be installed on a false car for safe testing?
A. Extra sensors
B. Hydraulic cushion
C. Spring loaded safeties
D. Counterweight
Rationale: Safeties engage in emergency conditions during false car
tests.
6. If the relief valve is set too low on a hydraulic elevator, what may
occur?
A. Overspeed
B. Hydro runs up with no load but won’t operate with full load
C. Brake failure
D. Excess heat in controller
Rationale: Insufficient relief pressure limits load capacity.
7. What is the significant safety standard for existing elevators?
A. NFPA 70
B. ASME A17.3
C. ICC IBC only
D. OSHA 1910
Rationale: A17.3 covers safety for existing installations.Georgia Rules
and Regulations
8. What is the typical meaning of “runby” in elevator setup?
A. Door dwell time
B. Distance car travels past terminal before reversing
C. Cable slack
, D. Traction loss
Rationale: Runby is the overtravel past terminal limits.
9. In elevator wiring, what does a MOV protect against?
A. Water ingress
B. Voltage spikes
C. Motor overload
D. Dead shorts
Rationale: Metal Oxide Varistors suppress surge voltages.
10. What’s the purpose of a brake in an elevator drive system?
A. Increase speed
B. Hold the car stationary
C. Balance load
D. Prevent door open
Rationale: Brakes keep the car in place when stopped.
11. Which code addresses accessibility for handicapped individuals?
A. NFPA 101
B. ANSI B20.1
C. ICC/ANSI A117.1
D. NEC
Rationale: A117.1 covers accessibility standards.Georgia Rules and
Regulations
12. In a DC motor with SCR drive added, what is done to the
interpoles?
A. Remove them
B. Leave them alone
C. Reverse polarity
D. Increase resistance
Rationale: Interpoles remain to maintain commutation.
13. During an elevator inspection, what must buffers do within
90 seconds?
A. Cool down
B. Fully extend under test load
C. Reset electronics
D. Activate doors
Rationale: Buffer extension indicates proper energy absorption.
Examination Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. What is the purpose of the governor in an elevator system?
A. To control door timing
B. To regulate overspeed protection
C. To power the controller
D. To increase traction
Rationale: The governor detects and responds to overspeed conditions,
triggering safety devices.
2. What does ASME A17.1 primarily cover?
A. Fire extinguisher placement
B. Safety code for elevators and escalators
C. Plumbing standards
D. Electrical outlet spacing
Rationale: ASME A17.1 is the American safety code governing
elevators/escalators in many jurisdictions including Georgia.Georgia
Rules and Regulations
3. In a traction elevator, what component provides friction for
movement?
A. Hydraulic ram
B. Counterweight roller
C. Drive sheave
D. Brake coil
, Rationale: The drive sheave transmits motor torque via ropes to move
the car by friction.
4. What voltage is commonly reduced from 480 V to supply control
circuits?
A. 12 V
B. 120 V
C. 240 V
D. 208 V
Rationale: A 480 V step-down transformer often produces 240 V for
control and logic circuits.
5. What must be installed on a false car for safe testing?
A. Extra sensors
B. Hydraulic cushion
C. Spring loaded safeties
D. Counterweight
Rationale: Safeties engage in emergency conditions during false car
tests.
6. If the relief valve is set too low on a hydraulic elevator, what may
occur?
A. Overspeed
B. Hydro runs up with no load but won’t operate with full load
C. Brake failure
D. Excess heat in controller
Rationale: Insufficient relief pressure limits load capacity.
7. What is the significant safety standard for existing elevators?
A. NFPA 70
B. ASME A17.3
C. ICC IBC only
D. OSHA 1910
Rationale: A17.3 covers safety for existing installations.Georgia Rules
and Regulations
8. What is the typical meaning of “runby” in elevator setup?
A. Door dwell time
B. Distance car travels past terminal before reversing
C. Cable slack
, D. Traction loss
Rationale: Runby is the overtravel past terminal limits.
9. In elevator wiring, what does a MOV protect against?
A. Water ingress
B. Voltage spikes
C. Motor overload
D. Dead shorts
Rationale: Metal Oxide Varistors suppress surge voltages.
10. What’s the purpose of a brake in an elevator drive system?
A. Increase speed
B. Hold the car stationary
C. Balance load
D. Prevent door open
Rationale: Brakes keep the car in place when stopped.
11. Which code addresses accessibility for handicapped individuals?
A. NFPA 101
B. ANSI B20.1
C. ICC/ANSI A117.1
D. NEC
Rationale: A117.1 covers accessibility standards.Georgia Rules and
Regulations
12. In a DC motor with SCR drive added, what is done to the
interpoles?
A. Remove them
B. Leave them alone
C. Reverse polarity
D. Increase resistance
Rationale: Interpoles remain to maintain commutation.
13. During an elevator inspection, what must buffers do within
90 seconds?
A. Cool down
B. Fully extend under test load
C. Reset electronics
D. Activate doors
Rationale: Buffer extension indicates proper energy absorption.
